X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fsequoia.h;h=f4eefae2f498654c62d9bb07ee67d86eb4984c7b;hb=72675dc6c06a48846d180106161d49dd714383cc;hp=555316ff63811598d64e6f365cd8c7330fd564d9;hpb=f9eabcb357ea294e3e01bfe26841bf51d6bd8f05;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 555316f..f4eefae 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -34,11 +34,19 @@ /* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */ #ifndef CONFIG_RAINIER #define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_HOSTNAME sequoia #else #define CONFIG_440GRX 1 /* Specific PPC440GRx */ +#define CONFIG_HOSTNAME rainier #endif #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ + +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + /* Detect Sequoia PLL input clock automatically via CPLD bit */ #define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \ 33333333 : 33000000) @@ -64,19 +72,9 @@ * Base addresses -- Note these are effective addresses where the actual * resources get mapped (not physical addresses). */ -#ifndef CONFIG_VIDEO -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kiB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kiB for malloc() */ -#else -#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */ -#endif - #define CFG_TLB_FOR_BOOT_FLASH 0x0003 #define CFG_BOOT_BASE_ADDR 0xf0000000 -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_MONITOR_BASE TEXT_BASE #define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ #define CFG_OCM_BASE 0xe0010000 /* ocm */ #define CFG_OCM_DATA_ADDR CFG_OCM_BASE @@ -108,14 +106,9 @@ * Serial Port */ #define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /* * Environment */ @@ -227,10 +220,7 @@ /* * I2C */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -247,80 +237,27 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifndef CONFIG_RAINIER -#define CONFIG_HOSTNAME sequoia -#define CFG_BOOTFILE "bootfile=sequoia/uImage\0" -#define CFG_DTBFILE "fdt_file=sequoia/sequoia.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME rainier -#define CFG_BOOTFILE "bootfile=rainier/uImage\0" -#define CFG_DTBFILE "fdt_file=rainier/rainier.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_ROOTPATH \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "addmisc=setenv bootargs ${bootargs}\0" \ - "flash_nfs=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm\0" \ - "fdt_file=sequoia/sequoia.dtb\0" \ - "fdt_addr=400000\0" \ - "net_nfs_fdt=tftp 200000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm 200000 - ${fdt_addr}\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=FC000000\0" \ "ramdisk_addr=FC180000\0" \ - "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ - "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ - "cp.b 200000 FFFA0000 60000\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_HAS_ETH0 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx */ - /* buffers & descriptors */ -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 1 @@ -347,35 +284,12 @@ #define CONFIG_ISO_PARTITION /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF #define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #ifdef CONFIG_440EPX @@ -407,35 +321,6 @@ #define CONFIG_SUPPORT_VFAT /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) - /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -/* * PCI stuff */ /* General PCI */ @@ -443,7 +328,7 @@ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */ /* CFG_PCI_MEMBASE */ /* Board-specific PCI */ #define CFG_PCI_TARGET_INIT @@ -453,13 +338,6 @@ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ /* - * For booting Linux, the board info and command line data have to be in the - * first 8 MB of memory, since this is the maximum mapped by the Linux kernel - * during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* * External Bus Controller (EBC) Setup */ @@ -577,23 +455,6 @@ } \ } -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #ifdef CONFIG_VIDEO #define CONFIG_BIOSEMU /* x86 bios emulator for vga bios */ #define CONFIG_ATI_RADEON_FB /* use radeon framebuffer driver */