X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fsequoia.h;h=7a120ed5a69e673478bbc644f94091aca5aec6ec;hb=d4db3b86a5e090e21db710bedbbe3e50d4c56428;hp=1f1beeaf2ed26d1c3bd7b0b50c775aaa3c5883aa;hpb=1254ff97abb7606ccd0d7bdcd9f22581c50fe535;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 1f1beea..7a120ed 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -45,7 +45,6 @@
  * Define this if you want support for video console with radeon 9200 pci card
  * Also set CONFIG_SYS_TEXT_BASE to 0xFFF80000 in board/amcc/sequoia/config.mk in this case
  */
-#undef CONFIG_VIDEO
 
 #ifdef CONFIG_VIDEO
 /*
@@ -55,7 +54,6 @@
 #define CONFIG_4xx_DCACHE		/* enable dcache		*/
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 #define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
 
 /*
@@ -151,7 +149,6 @@
  */
 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
 
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR	(0xa8>>1)
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
@@ -162,14 +159,6 @@
 #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET	0
 #define CONFIG_4xx_CONFIG_BLOCKSIZE		16
 
-/* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
-#define CONFIG_DTT_LM75		1	/* ON Semi's LM75		*/
-#define CONFIG_DTT_AD7414	1	/* use AD7414			*/
-#define CONFIG_DTT_SENSORS	{0}	/* Sensor addresses		*/
-#define CONFIG_SYS_DTT_MAX_TEMP	70
-#define CONFIG_SYS_DTT_LOW_TEMP	-30
-#define CONFIG_SYS_DTT_HYSTERESIS	3
-
 /*
  * Default environment variables
  */
@@ -195,16 +184,13 @@
 
 /* USB */
 #ifdef CONFIG_440EPX
-
-#undef CONFIG_USB_EHCI	/* OHCI by default */
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_USB_EHCI_PPC4XX
 #define CONFIG_SYS_PPC4XX_USB_ADDR	0xe0000300
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_EHCI_MMIO_BIG_ENDIAN
 #define CONFIG_EHCI_DESC_BIG_ENDIAN
-#else /* CONFIG_USB_EHCI */
+#else /* CONFIG_USB_EHCI_HCD */
 #define CONFIG_USB_OHCI_NEW
 #define CONFIG_SYS_OHCI_BE_CONTROLLER
 
@@ -215,29 +201,21 @@
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
 #endif
 
-#define CONFIG_USB_STORAGE
 /* Comment this out to enable USB 1.1 device */
 #define USB_2_0_DEVICE
 
 #endif /* CONFIG_440EPX */
 
 /* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
 
 /*
  * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_CMD_CHIP_CONFIG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_FAT
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SDRAM
 
 #ifdef CONFIG_440EPX
-#define CONFIG_CMD_USB
 #endif
 
 #ifndef CONFIG_RAINIER
@@ -270,17 +248,13 @@
 #define CONFIG_LOGBUFFER
 #define CONFIG_SYS_POST_CACHE_ADDR	0x7fff0000	/* free virtual address     */
 
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* Otherwise it catches logbuffer as output */
-
 #define CONFIG_SUPPORT_VFAT
 
 /*
  * PCI stuff
  */
 /* General PCI */
-#define CONFIG_PCI			/* include pci support		*/
 #define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
 #define CONFIG_SYS_PCI_CACHE_LINE_SIZE	0	/* to avoid problems with PNP	*/
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
 #define CONFIG_SYS_PCI_TARGBASE	0x80000000	/* PCIaddr mapped to	*/
@@ -415,12 +389,8 @@
 #define CONFIG_ATI_RADEON_FB		/* use radeon framebuffer driver */
 #define VIDEO_IO_OFFSET			0xe8000000
 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS		VIDEO_IO_OFFSET
-#define CONFIG_VIDEO_SW_CURSOR
 #define CONFIG_VIDEO_LOGO
-#define CONFIG_CFB_CONSOLE
 #define CONFIG_SPLASH_SCREEN
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_CMD_BMP
 #endif
 
 #endif /* __CONFIG_H */