X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fsbc8641d.h;h=efc787e999382ae9f6266fd8dbf0752371522442;hb=00b1883a4cac59d97cd297b1a3a398db85982865;hp=54eac38b86fab216ff179542c7b1e2c4eb04bb59;hpb=1d1ab638f8b5961e4972d29394e573afb39667be;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index 54eac38..efc787e 100644
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -53,14 +53,17 @@
 #define CONFIG_PCI1		1	/* PCIE controler 1 (slot 1) */
 #define CONFIG_PCI2		1	/* PCIE controler 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
 
-#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
+#define CONFIG_HIGH_BATS	1	/* High BATs supported and enabled */
+
 #undef CONFIG_SPD_EEPROM		/* Do not use SPD EEPROM for DDR setup*/
 #undef CONFIG_DDR_DLL			/* possible DLL fix needed */
 #define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
-#undef CONFIG_DDR_ECC  			/* only for ECC DDR module */
+#undef CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 #define CONFIG_NUM_DDR_CONTROLLERS     2
@@ -93,7 +96,7 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
-#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
 #define CFG_CCSRBAR		0xf8000000	/* relocated CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
@@ -135,7 +138,7 @@
     #define CFG_DDR_CS1_CONFIG	0x00000000
     #define CFG_DDR_CS2_CONFIG	0x00000000
     #define CFG_DDR_CS3_CONFIG	0x00000000
-    #define CFG_DDR_EXT_REFRESH 0x00000000
+    #define CFG_DDR_TIMING_3 0x00000000
     #define CFG_DDR_TIMING_0	0x00220802
     #define CFG_DDR_TIMING_1	0x38377322
     #define CFG_DDR_TIMING_2	0x002040c7
@@ -218,9 +221,9 @@
 #undef	CFG_FLASH_CHECKSUM
 #define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
 
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
 #define CFG_FLASH_CFI
 #define CFG_WRITE_SWAPPED_DATA
 #define CFG_FLASH_EMPTY_INFO
@@ -235,14 +238,14 @@
 #else
 #define CFG_INIT_RAM_ADDR	0xf8400000	/* Initial RAM address */
 #endif
-#define CFG_INIT_RAM_END    	0x4000	    	/* End of used area in RAM */
+#define CFG_INIT_RAM_END	0x4000		/* End of used area in RAM */
 
-#define CFG_GBL_DATA_SIZE  	128		/* num bytes initial data */
+#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_LEN	    	(256 * 1024)    /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN	    	(128 * 1024)    /* Reserved for malloc */
+#define CFG_MONITOR_LEN		(256 * 1024)    /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024)    /* Reserved for malloc */
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX     1
@@ -267,13 +270,9 @@
 /*
  * Pass open firmware flat tree to kernel
  */
-#define CONFIG_OF_FLAT_TREE	1
-#define CONFIG_OF_BOARD_SETUP	1
-
-#define OF_CPU		"PowerPC,8641@0"
-#define OF_SOC		"soc@f8000000"
-#define OF_TBCLK	(bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH	"/soc@f8000000/serial@4500"
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
 
 #define CFG_64BIT_VSPRINTF	1
 #define CFG_64BIT_STRTOUL	1
@@ -326,7 +325,7 @@
 #undef CFG_SCSI_SCAN_BUS_REVERSE
 
 #define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
@@ -334,7 +333,7 @@
 #if !defined(CONFIG_PCI_PNP)
     #define PCI_ENET0_IOADDR	0xe0000000
     #define PCI_ENET0_MEMADDR	0xe0000000
-    #define PCI_IDSEL_NUMBER	0x0c 	/* slot0->3(IDSEL)=12->15 */
+    #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
 #endif
 
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
@@ -346,7 +345,7 @@
 #define CONFIG_SATA_ULI5288
 #define CFG_SCSI_MAX_SCSI_ID	4
 #define CFG_SCSI_MAX_LUN	1
-#define CFG_SCSI_MAX_DEVICE 	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAX_DEVICE	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
 #define CFG_SCSI_MAXDEVICE	CFG_SCSI_MAX_DEVICE
 #endif
 
@@ -355,7 +354,7 @@
 #if defined(CONFIG_TSEC_ENET)
 
 #ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 	1
+#define CONFIG_NET_MULTI	1
 #endif
 
 /* #define CONFIG_MII		1 */	/* MII PHY management */
@@ -479,6 +478,7 @@
 #include <config_cmd_default.h>
     #define CONFIG_CMD_PING
     #define CONFIG_CMD_I2C
+    #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI