X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fsbc8548.h;h=9df8604af712a368d5c4982583b0a42b5b944823;hb=4862830b696a6d0750e19d32a82553cdb41a85f8;hp=e9f9d30d52a860c13133cd94292b9ffd9739a087;hpb=4ddc981225288e68d45eb8e33271d1481920086f;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index e9f9d30..9df8604 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -1,9 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2007,2009 Wind River Systems <www.windriver.com>
  * Copyright 2007 Embedded Specialties, Inc.
  * Copyright 2004, 2007 Freescale Semiconductor.
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 /*
@@ -36,10 +35,6 @@
 /*
  * High Level Configuration Options
  */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_MPC8548		1	/* MPC8548 specific */
-#define CONFIG_SBC8548		1	/* SBC8548 board specific */
 
 /*
  * If you want to boot from the SODIMM flash, instead of the soldered
@@ -47,14 +42,6 @@
  */
 #undef CONFIG_SYS_ALT_BOOT
 
-#ifndef CONFIG_SYS_TEXT_BASE
-#ifdef CONFIG_SYS_ALT_BOOT
-#define CONFIG_SYS_TEXT_BASE	0xfff00000
-#else
-#define CONFIG_SYS_TEXT_BASE	0xfffa0000
-#endif
-#endif
-
 #undef CONFIG_RIO
 
 #ifdef CONFIG_PCI
@@ -65,13 +52,10 @@
 #define CONFIG_FSL_PCIE_RESET   1	/* need PCIe reset errata */
 #endif
 
-#define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
-
 /*
  * Below assumes that CCB:SYSCLK remains unchanged at 6:1 via SW2:[1-4]
  */
@@ -91,8 +75,6 @@
  */
 #define CONFIG_ENABLE_36BIT_PHYS	1
 
-#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
-
 #undef	CONFIG_SYS_DRAM_TEST			/* memory test, takes time */
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
@@ -101,8 +83,6 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR2
-#undef CONFIG_FSL_DDR_INTERACTIVE
 #undef CONFIG_DDR_ECC			/* only for ECC DDR module */
 /*
  * A hardware errata caused the LBC SDRAM SPD and the DDR2 SPD
@@ -122,7 +102,6 @@
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_VERY_BIG_RAM
 
-#define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	2
 
@@ -265,8 +244,6 @@
 
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 
 /* CS5 = Local bus peripherals controlled by the EPLD */
@@ -404,7 +381,6 @@
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024) /* Reserved for malloc */
 
 /* Serial Port */
-#define CONFIG_CONS_INDEX	1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		(400000000 / CONFIG_SYS_CLK_DIV)
@@ -470,7 +446,6 @@
 
 #if defined(CONFIG_TSEC_ENET)
 
-#define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_TSEC1	1
 #define CONFIG_TSEC1_NAME	"eTSEC0"
 #define CONFIG_TSEC2	1
@@ -488,13 +463,11 @@
 
 /* Options are: eTSEC[0-3] */
 #define CONFIG_ETHPRIME		"eTSEC0"
-#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #endif	/* CONFIG_TSEC_ENET */
 
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_SIZE		0x2000
 #if CONFIG_SYS_TEXT_BASE == 0xfff00000	/* Boot from 64MB SODIMM */
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x80000)
@@ -513,36 +486,13 @@
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
-#endif
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_CMDLINE_EDITING			/* undef to save memory */
-#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
 
 /*
  * For booting Linux, the board info and command line data
@@ -565,7 +515,7 @@
 
 #define CONFIG_IPADDR	 192.168.0.55
 
-#define CONFIG_HOSTNAME	 sbc8548
+#define CONFIG_HOSTNAME	 "sbc8548"
 #define CONFIG_ROOTPATH	 "/opt/eldk/ppc_85xx"
 #define CONFIG_BOOTFILE	 "/uImage"
 #define CONFIG_UBOOTPATH /u-boot.bin	/* TFTP server */
@@ -576,10 +526,6 @@
 
 #define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/
 
-#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs*/
-
-#define CONFIG_BAUDRATE	115200
-
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 "netdev=eth0\0"						\
 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"				\