X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fsama5d3_xplained.h;h=8a9a19d38e61bcd0929a7a43f00c10695f3a3100;hb=d01806a8fcbdaedcc67cead56ece572021d97ab7;hp=76533e3954fb2e2192394ac87351a31ea6d63beb;hpb=2218b32d88f9b4b4484cea9a8b034ddab0be298b;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/sama5d3_xplained.h b/include/configs/sama5d3_xplained.h
index 76533e3..8a9a19d 100644
--- a/include/configs/sama5d3_xplained.h
+++ b/include/configs/sama5d3_xplained.h
@@ -1,10 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Configuration settings for the SAMA5D3 Xplained board.
  *
  * Copyright (C) 2014 Atmel Corporation
  *		      Bo Shen <voice.shen@atmel.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -16,16 +15,15 @@
  * This needs to be defined for the OHCI code to work but it is defined as
  * ATMEL_ID_UHPHS in the CPU specific header files.
  */
-#define ATMEL_ID_UHP			ATMEL_ID_UHPHS
+#define ATMEL_ID_UHP			32
 
 /*
  * Specify the clock enable bit in the PMC_SCER register.
  */
-#define ATMEL_PMC_UHP			AT91SAM926x_PMC_UHP
+#define ATMEL_PMC_UHP			(1 <<  6)
 
 /* SDRAM */
-#define CONFIG_NR_DRAM_BANKS		1
-#define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
+#define CONFIG_SYS_SDRAM_BASE           0x20000000
 #define CONFIG_SYS_SDRAM_SIZE		0x10000000
 
 #ifdef CONFIG_SPL_BUILD
@@ -36,50 +34,30 @@
 #endif
 
 /* NAND flash */
-#define CONFIG_CMD_NAND
-
 #ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_ATMEL
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_BASE		0x60000000
 /* our ALE is AD21 */
 #define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
 /* our CLE is AD22 */
 #define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
 #define CONFIG_SYS_NAND_ONFI_DETECTION
-/* PMECC & PMERRLOC */
-#define CONFIG_ATMEL_NAND_HWECC
-#define CONFIG_ATMEL_NAND_HW_PMECC
-#define CONFIG_PMECC_CAP		4
-#define CONFIG_PMECC_SECTOR_SIZE	512
-#define CONFIG_CMD_NAND_TRIMFFS
-
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
 #endif
 
 /* USB */
-
 #ifdef CONFIG_CMD_USB
 #define CONFIG_USB_ATMEL
 #define CONFIG_USB_ATMEL_CLK_SEL_UPLL
 #define CONFIG_USB_OHCI_NEW
 #define CONFIG_SYS_USB_OHCI_CPU_INIT
-#define CONFIG_SYS_USB_OHCI_REGS_BASE		ATMEL_BASE_OHCI
+#define CONFIG_SYS_USB_OHCI_REGS_BASE		0x00600000
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME		"SAMA5D3 Xplained"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
 #endif
 
 #define CONFIG_SYS_LOAD_ADDR			0x22000000 /* load address */
 
-#if CONFIG_SYS_USE_NANDFLASH
-/* override the bootcmd, bootargs and other configuration for nandflash env */
-#elif CONFIG_SYS_USE_MMC
-/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#endif
-
 /* SPL */
-#define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_TEXT_BASE		0x300000
 #define CONFIG_SPL_MAX_SIZE		0x18000
 #define CONFIG_SPL_BSS_START_ADDR	0x20000000
@@ -89,14 +67,14 @@
 
 #define CONFIG_SYS_MONITOR_LEN		(512 << 10)
 
-#ifdef CONFIG_SYS_USE_MMC
-#define CONFIG_SPL_LDSCRIPT		arch/arm/mach-at91/armv7/u-boot-spl.lds
+#ifdef CONFIG_SD_BOOT
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"
 
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_NAND_BOOT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
+#endif
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_SIZE	0x800
@@ -104,8 +82,5 @@
 #define CONFIG_SYS_NAND_OOBSIZE		64
 #define CONFIG_SYS_NAND_BLOCK_SIZE	0x20000
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0x0
-#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
-
-#endif
 
 #endif