X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fqemu-ppce500.h;h=c26810723e5969bbfadac0efb2e1aef2390d82ae;hb=1b330894bd40cb0d7ef37bb761d104820f794aae;hp=10e014d33c467c31908000c539f54acfa843fb19;hpb=8854070784450f7ade382c5792b2721fbe27315a;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/qemu-ppce500.h b/include/configs/qemu-ppce500.h
index 10e014d..c268107 100644
--- a/include/configs/qemu-ppce500.h
+++ b/include/configs/qemu-ppce500.h
@@ -12,11 +12,6 @@
 
 #define CONFIG_CMD_REGINFO
 
-/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500			/* BOOKE e500 family */
-#define CONFIG_QEMU_E500
-
 #undef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xf01000 /* 15 MB */
 
@@ -24,7 +19,6 @@
 
 #define CONFIG_SYS_RAMBOOT
 
-#define CONFIG_PCI			/* Enable PCI/PCIE */
 #define CONFIG_PCI1		1	/* PCI controller 1 */
 #define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
@@ -42,15 +36,18 @@
 #define CONFIG_PANIC_HANG	/* do not reset board on panic */
 
 /* Needed to fill the ccsrbar pointer */
-#define CONFIG_BOARD_EARLY_INIT_F
 
 /* Virtual address to CCSRBAR */
 #define CONFIG_SYS_CCSRBAR		0xe0000000
 /* Physical address should be a function call */
 #ifndef __ASSEMBLY__
 extern unsigned long long get_phys_ccsrbar_addr_early(void);
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH (get_phys_ccsrbar_addr_early() >> 32)
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW get_phys_ccsrbar_addr_early()
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
 #endif
-#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 
 /* Virtual address range for PCI region maps */
 #define CONFIG_SYS_PCI_MAP_START	0x80000000
@@ -70,8 +67,6 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 
 #define CONFIG_SYS_CLK_FREQ        33000000
 
-#define CONFIG_SYS_NO_FLASH
-
 #define CONFIG_SYS_BOOT_BLOCK		0x00000000	/* boot TLB */
 
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
@@ -97,7 +92,6 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
 
 #define CONFIG_CONS_INDEX	1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0))
@@ -108,19 +102,6 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
-
 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
@@ -128,17 +109,11 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-#define CONFIG_E1000
 
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #endif	/* CONFIG_PCI */
 
 #define CONFIG_LBA48
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
 
 /*
  * Environment
@@ -152,19 +127,9 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
 
 #ifdef CONFIG_PCI
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
 #endif
 
 /*
@@ -197,9 +162,6 @@ extern unsigned long long get_phys_ccsrbar_addr_early(void);
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR		1000000
 
-#define CONFIG_BAUDRATE	115200
-
-#define CONFIG_BOOTDELAY        1
 #define CONFIG_BOOTCOMMAND		\
 	"test -n \"$qemu_kernel_addr\" && bootm $qemu_kernel_addr - $fdt_addr_r\0"