X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fp1_twr.h;h=f672ffe43cc5afe275ac0b779b62b07227060b00;hb=3c594d34c4addc962b2bd6ed2d16f3ce24ab1627;hp=46f5f0f70e5a5a4af0fc43841292bd659afbc0bf;hpb=677f970bc62a661690b3431543d5a5d5e682ba70;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
index 46f5f0f..f672ffe 100644
--- a/include/configs/p1_twr.h
+++ b/include/configs/p1_twr.h
@@ -10,8 +10,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define	CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_FSL_CLK
 #if defined(CONFIG_TWR_P1025)
 #define CONFIG_BOARDNAME "TWR-P1025"
 #define CONFIG_P1025
@@ -49,8 +47,8 @@
 
 #define CONFIG_FSL_ELBC
 #define CONFIG_PCI
-#define CONFIG_PCIE1	/* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2	/* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE1	/* PCIE controller 1 (slot 1) */
+#define CONFIG_PCIE2	/* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
 #define CONFIG_FSL_PCIE_RESET	/* need PCIe reset errata */
@@ -216,7 +214,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_CONS_INDEX		1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
@@ -227,23 +224,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL			/* Use FSL common I2C driver */
@@ -263,7 +243,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 /* enable read and write access to EEPROM */
 #define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -272,7 +251,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * eSPI - Enhanced SPI
  */
 #define CONFIG_HARD_SPI
-#define CONFIG_FSL_ESPI
 
 #if defined(CONFIG_PCI)
 /*
@@ -422,9 +400,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * Command line configuration.
  */
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -436,10 +411,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_USB_EHCI
 
 #ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
 #endif
 #endif
 
@@ -448,14 +421,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
 #define CONFIG_GENERIC_MMC
 #endif
 
 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
 		 || defined(CONFIG_FSL_SATA)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 #endif
 
@@ -496,7 +466,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR	1000000
 
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
 #define CONFIG_BOOTARGS	/* the boot command will set bootargs */
 
 #define CONFIG_BAUDRATE	115200
@@ -542,7 +511,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 "consoledev=ttyS0\0"	\
 "ramdiskaddr=2000000\0"	\
 "ramdiskfile=rootfs.ext2.gz.uboot\0"	\
-"fdtaddr=c00000\0"	\
+"fdtaddr=1e00000\0"	\
 "bdev=sda1\0"	\
 "norbootaddr=ef080000\0"	\
 "norfdtaddr=ef040000\0"	\