X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fp1_twr.h;h=e02c31db2acdba1d2154d28d44f7507b0afbcf76;hb=4bafceff0e9e5a36908031e41c69a6b37e82da58;hp=d403f8461778568e988f1b2ad1f50bbf5b2fcd96;hpb=f1cc97764be4383d2aeb56d5ba5415439a1d5c97;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
index d403f84..e02c31d 100644
--- a/include/configs/p1_twr.h
+++ b/include/configs/p1_twr.h
@@ -22,14 +22,9 @@
 #define CONFIG_RAMBOOT_SDCARD
 #define CONFIG_SYS_RAMBOOT
 #define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE		0x11000000
 #define CONFIG_RESET_VECTOR_ADDRESS	0x110bfffc
 #endif
 
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE		0xeff40000
-#endif
-
 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
 #endif
@@ -50,10 +45,7 @@
 #define CONFIG_TSEC_ENET	/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
-#define CONFIG_CMD_SATA
-#define CONFIG_SATA_SIL3114
 #define CONFIG_SYS_SATA_MAX_DEVICE	2
-#define CONFIG_LIBATA
 #define CONFIG_LBA48
 
 #ifndef __ASSEMBLY__
@@ -72,7 +64,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x1fffffff
-#define CONFIG_PANIC_HANG	/* do not reset board on panic */
 
 #define CONFIG_SYS_CCSRBAR		0xffe00000
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
@@ -230,7 +221,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_I2C_PCA9555_ADDR	0x23
 
 /* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -268,8 +258,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xffc00000
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
 
-#define CONFIG_CMD_PCI
-
 #define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
 #endif /* CONFIG_PCI */
 
@@ -297,8 +285,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_ETHPRIME	"eTSEC1"
 
-#define CONFIG_PHY_GIGE	1	/* Include GbE speed/duplex detection */
-
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #undef CONFIG_HAS_ETH2
@@ -352,28 +338,20 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=ec000000.nor"
-#define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:256k(vsc7385-firmware)," \
-			"256k(dtb),5632k(kernel),57856k(fs)," \
-			"256k(qe-ucode-firmware),1280k(u-boot)"
 
 /*
  * Environment
  */
 #ifdef CONFIG_SYS_RAMBOOT
 #ifdef CONFIG_RAMBOOT_SDCARD
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_SYS_MMC_ENV_DEV	0
 #else
-#define CONFIG_ENV_IS_NOWHERE	/* Store ENV in memory only */
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE		0x2000
 #endif
 #else
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR	(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
@@ -383,20 +361,12 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
 
 /*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-/*
  * USB
  */
 #define CONFIG_HAS_FSL_DR_USB
 
 #if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #endif
@@ -412,18 +382,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory */
-#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 
 /*
  * For booting Linux, the board info and command line data
@@ -444,10 +403,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR	1000000
 
-#define CONFIG_BOOTARGS	/* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE	115200
-
 #define	CONFIG_EXTRA_ENV_SETTINGS	\
 "netdev=eth0\0"	\
 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"	\