X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fp1_twr.h;h=d5f576946329cd87d906d61b7c31eb10f9a41ae7;hb=85fc970d74d09f33fcdcc649e73c5dc4f5334605;hp=63825b0bde790b594f924132f4989b79cbb006c0;hpb=0b8404332ed08799ca0630e4cc868df039f206e3;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
index 63825b0..d5f5769 100644
--- a/include/configs/p1_twr.h
+++ b/include/configs/p1_twr.h
@@ -40,7 +40,6 @@
 
 #define CONFIG_MP
 
-#define CONFIG_FSL_ELBC
 #define CONFIG_PCIE1	/* PCIE controller 1 (slot 1) */
 #define CONFIG_PCIE2	/* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
@@ -51,7 +50,6 @@
 #define CONFIG_TSEC_ENET	/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
-#define CONFIG_CMD_SATA
 #define CONFIG_SATA_SIL3114
 #define CONFIG_SYS_SATA_MAX_DEVICE	2
 #define CONFIG_LIBATA
@@ -71,8 +69,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_L2_CACHE
 #define CONFIG_BTB
 
-#define CONFIG_BOARD_EARLY_INIT_F	/* Call board_pre_init */
-
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x1fffffff
 #define CONFIG_PANIC_HANG	/* do not reset board on panic */
@@ -233,7 +229,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_I2C_PCA9555_ADDR	0x23
 
 /* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -274,7 +269,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_CMD_PCI
 
 #define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #endif /* CONFIG_PCI */
 
 #if defined(CONFIG_TSEC_ENET)
@@ -356,7 +350,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
 #define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT "nor0=ec000000.nor"
 #define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:256k(vsc7385-firmware)," \
@@ -368,16 +361,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #ifdef CONFIG_SYS_RAMBOOT
 #ifdef CONFIG_RAMBOOT_SDCARD
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_SYS_MMC_ENV_DEV	0
 #else
-#define CONFIG_ENV_IS_NOWHERE	/* Store ENV in memory only */
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE		0x2000
 #endif
 #else
-#define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR	(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
@@ -389,7 +379,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -398,9 +387,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_HAS_FSL_DR_USB
 
 #if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #endif
@@ -409,12 +396,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
-		 || defined(CONFIG_FSL_SATA)
-#define CONFIG_DOS_PARTITION
 #endif
 
 #undef CONFIG_WATCHDOG	/* watchdog disabled */
@@ -456,8 +437,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_BOOTARGS	/* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE	115200
-
 #define	CONFIG_EXTRA_ENV_SETTINGS	\
 "netdev=eth0\0"	\
 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"	\