X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fp1_p2_rdb_pc.h;h=a72a57c904664d342d3cc3057d0d8790841670e1;hb=3bf926c0dd01e7beb3a6815b2e0f28e989fe4120;hp=77f3d8159374afb309191ff07c7404e3ce729b02;hpb=4593637b135b6f8f46a086f73b6ee10849de11bf;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index 77f3d81..a72a57c 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -174,7 +174,6 @@
 #define CONFIG_SPL_MMC_MINIMAL
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
-#define CONFIG_FSL_LAW                 /* Use common FSL init code */
 #define CONFIG_SYS_TEXT_BASE		0x11001000
 #define CONFIG_SPL_TEXT_BASE		0xf8f81000
 #define CONFIG_SPL_PAD_TO		0x20000
@@ -195,7 +194,6 @@
 #define CONFIG_SPL_SPI_FLASH_MINIMAL
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
-#define CONFIG_FSL_LAW         /* Use common FSL init code */
 #define CONFIG_SYS_TEXT_BASE		0x11001000
 #define CONFIG_SPL_TEXT_BASE		0xf8f81000
 #define CONFIG_SPL_PAD_TO		0x20000
@@ -260,13 +258,8 @@
 #endif
 #endif
 
-/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500
-
 #define CONFIG_MP
 
-#define CONFIG_FSL_ELBC
 #define CONFIG_PCIE1	/* PCIE controller 1 (slot 1) */
 #define CONFIG_PCIE2	/* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
@@ -274,11 +267,9 @@
 #define CONFIG_FSL_PCIE_RESET	/* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
 
-#define CONFIG_FSL_LAW
 #define CONFIG_TSEC_ENET	/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
-#define CONFIG_CMD_SATA
 #define CONFIG_SATA_SIL
 #define CONFIG_SYS_SATA_MAX_DEVICE	2
 #define CONFIG_LIBATA
@@ -298,8 +289,6 @@
 #define CONFIG_L2_CACHE
 #define CONFIG_BTB
 
-#define CONFIG_BOARD_EARLY_INIT_F	/* Call board_pre_init */
-
 #define CONFIG_ENABLE_36BIT_PHYS
 
 #ifdef CONFIG_PHYS_64BIT
@@ -321,7 +310,6 @@
 #endif
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM 1
@@ -339,7 +327,6 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 
 /* Default settings for DDR3 */
@@ -643,7 +630,6 @@
 #define CONFIG_SYS_I2C_PCA9557_ADDR	0x18
 
 /* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -707,7 +693,6 @@
 #define CONFIG_CMD_PCI
 
 #define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #endif /* CONFIG_PCI */
 
 #if defined(CONFIG_TSEC_ENET)
@@ -827,8 +812,6 @@
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_DATE
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -837,9 +820,7 @@
 #define CONFIG_HAS_FSL_DR_USB
 
 #if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #endif
@@ -849,17 +830,9 @@
 #define CONFIG_USB_MAX_CONTROLLER_COUNT	1
 #endif
 
-#define CONFIG_MMC
-
 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
-		 || defined(CONFIG_FSL_SATA)
-#define CONFIG_DOS_PARTITION
 #endif
 
 #undef CONFIG_WATCHDOG	/* watchdog disabled */
@@ -905,8 +878,6 @@
 
 #define CONFIG_BOOTARGS	/* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE	115200
-
 #ifdef __SW_BOOT_NOR
 #define __NOR_RST_CMD	\
 norboot=i2c dev 1; i2c mw 18 1 __SW_BOOT_NOR 1; \