X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fomap3_logic.h;h=1af87b271c4fa3e551c129877bcaffada566c4c7;hb=b8e09898919e23c5d7f1934be7bf9a3a6f0deb0e;hp=90292ae31211f1922f696deacbd16ecffc66b3a7;hpb=d22c8be964a870f59d2fdab6c67cefa0c4799364;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index 90292ae..1af87b2 100644
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -14,39 +14,10 @@
 
 #include <configs/ti_omap3_common.h>
 
-/*
- * We are only ever GP parts and will utilize all of the "downloaded image"
- * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
- * order to allow for BCH8 to fit in.
- */
-
-#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
-/* Hardware drivers */
-
-/* I2C */
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM AT24C64      */
-
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_USB_EHCI_OMAP
-#endif
-#ifdef CONFIG_USB_EHCI_OMAP
-#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO	4
-#endif
-
 /* Board NAND Info. */
-#ifdef CONFIG_NAND
+#ifdef CONFIG_MTD_RAW_NAND
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	  /* Max number of */
 						  /* NAND devices */
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT	64
-#define CONFIG_SYS_NAND_PAGE_SIZE	2048
-#define CONFIG_SYS_NAND_OOBSIZE		64
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
 #define CONFIG_SYS_NAND_ECCPOS		{2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
 					 13, 14, 16, 17, 18, 19, 20, 21, 22, \
 					 23, 24, 25, 26, 27, 28, 30, 31, 32, \
@@ -56,7 +27,6 @@
 
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	13
-#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
 #define CONFIG_SYS_NAND_MAX_OOBFREE	2
 #define CONFIG_SYS_NAND_MAX_ECCPOS	56
 #endif
@@ -65,8 +35,6 @@
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	DEFAULT_LINUX_BOOT_ENV \
-	"mtdids=" CONFIG_MTDIDS_DEFAULT "\0"	\
-	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
 	"mmcdev=0\0" \
 	"finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \
 	"mmcrootfstype=ext4 rootwait\0" \
@@ -117,7 +85,6 @@
 		"nfsroot=${nfsrootpath} " \
 		"ip=${ipaddr}:${tftpserver}:${gatewayip}:${netmask}::eth0:off\0" \
 	"nfsrootpath=/opt/nfs-exports/omap\0" \
-	"autoload=no\0" \
 	"fdtimage=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
 	"loadfdt=mmc rescan; " \
 		"load mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
@@ -172,15 +139,9 @@
 	"nandboot=run nandbootcommon; "\
 		"bootm ${loadaddr} - ${fdtaddr}\0"\
 
-#define CONFIG_BOOTCOMMAND \
-	"run autoboot"
-
 /* Miscellaneous configurable options */
 
 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)
-#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
-					0x01F00000) /* 31MB */
 
 /* FLASH and environment organization */
 
@@ -189,22 +150,6 @@
 #define CONFIG_SYS_FLASH_BASE		0x10000000
 #endif
 
-#define CONFIG_SYS_MAX_FLASH_SECT	256
-#define CONFIG_SYS_MAX_FLASH_BANKS	1
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
 #define CONFIG_SYS_FLASH_SIZE		0x4000000
 
-/* Monitor at start of flash */
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
-#define CONFIG_ENV_ADDR			0x260000
-
-/* Defines for SPL */
-
-/* NAND: SPL falcon mode configs */
-#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS	0x280000
-#endif
-
 #endif /* __CONFIG_H */