X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fomap3_evm.h;h=6709edc8635218587874f0e91491be8e2aaa49bb;hb=206c00f26f56af02686cb69bfe5c75e979063171;hp=f4498a9bcc32c5b6f0d5cb3eebdc753605fcacd7;hpb=ea393eb1d6a786fc2e895f90abb5f7e7541aef45;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index f4498a9..6709edc 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -32,7 +32,6 @@ #ifndef __CONFIG_H #define __CONFIG_H -#include /* * High Level Configuration Options @@ -46,6 +45,12 @@ #include /* get chip and board defs */ #include +/* + * Display CPU and Board information + */ +#define CONFIG_DISPLAY_CPUINFO 1 +#define CONFIG_DISPLAY_BOARDINFO 1 + /* Clock Defines */ #define V_OSCK 26000000 /* Clock output from T2 */ #define V_SCLK (V_OSCK >> 1) @@ -61,12 +66,11 @@ /* * Size of malloc() pool */ -#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */ +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ /* Sector */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K) +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) #define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */ /* initial data */ - /* * Hardware drivers */ @@ -97,6 +101,9 @@ #define CONFIG_OMAP3_MMC 1 #define CONFIG_DOS_PARTITION 1 +/* DDR - I use Micron DDR */ +#define CONFIG_OMAP3_MICRON_DDR 1 + /* commands to include */ #include @@ -116,6 +123,7 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH +#define CONFIG_HARD_I2C 1 #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_SYS_I2C_SLAVE 1 #define CONFIG_SYS_I2C_BUS 0 @@ -123,6 +131,11 @@ #define CONFIG_DRIVER_OMAP34XX_I2C 1 /* + * TWL4030 + */ +#define CONFIG_TWL4030_POWER 1 + +/* * Board NAND Info. */ #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ @@ -133,18 +146,7 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ /* NAND devices */ -#define SECTORSIZE 512 - -#define NAND_ALLOW_ERASE_ALL -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 - -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 -#define NAND_NO_RB 1 -#define CONFIG_SYS_NAND_WP +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #define CONFIG_JFFS2_NAND /* nand device jffs2 lives on */ @@ -156,6 +158,8 @@ /* Environment information */ #define CONFIG_BOOTDELAY 10 +#define CONFIG_BOOTFILE uImage + #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ "console=ttyS2,115200n8\0" \ @@ -167,7 +171,7 @@ "rootfstype=jffs2\0" \ "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \ "bootscript=echo Running bootscript from mmc ...; " \ - "autoscr ${loadaddr}\0" \ + "source ${loadaddr}\0" \ "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ @@ -178,7 +182,7 @@ "bootm ${loadaddr}\0" \ #define CONFIG_BOOTCOMMAND \ - "if mmcinit; then " \ + "if mmc init; then " \ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ @@ -212,31 +216,27 @@ #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ 0x01F00000) /* 31MB */ -#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, */ - /* in Hz */ - #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */ /* address */ /* - * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by - * 32KHz clk, or from external sig. This rate is divided by a local divisor. + * OMAP3 has 12 GP timers, they can be driven by the system clock + * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). + * This rate is divided by a local divisor. */ -#define V_PVT 7 - #define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 -#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */ -#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PVT)) +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_HZ 1000 /*----------------------------------------------------------------------- * Stack sizes * * The stack sizes are set up in start.S using the settings below */ -#define CONFIG_STACKSIZE SZ_128K /* regular stack */ +#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */ #ifdef CONFIG_USE_IRQ -#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */ -#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */ +#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */ +#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */ #endif /*----------------------------------------------------------------------- @@ -244,7 +244,7 @@ */ #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */ +#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */ #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 /* SDRAM Bank Allocation method */ @@ -263,7 +263,7 @@ #define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */ /* on one chip */ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */ -#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ #define CONFIG_SYS_FLASH_BASE boot_flash_base @@ -295,8 +295,7 @@ #define CONFIG_SYS_JFFS2_NUM_BANKS 1 #ifndef __ASSEMBLY__ -extern gpmc_csx_t *nand_cs_base; -extern gpmc_t *gpmc_cfg_base; +extern struct gpmc *gpmc_cfg; extern unsigned int boot_flash_base; extern volatile unsigned int boot_flash_env_addr; extern unsigned int boot_flash_off; @@ -304,32 +303,16 @@ extern unsigned int boot_flash_sec; extern unsigned int boot_flash_type; #endif - -#define WRITE_NAND_COMMAND(d, adr)\ - writel(d, &nand_cs_base->nand_cmd) -#define WRITE_NAND_ADDRESS(d, adr)\ - writel(d, &nand_cs_base->nand_adr) -#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat) -#define READ_NAND(adr) readl(&nand_cs_base->nand_dat) - -/* Other NAND Access APIs */ -#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \ - while (0) -#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \ - while (0) -#define NAND_DISABLE_CE(nand) -#define NAND_ENABLE_CE(nand) -#define NAND_WAIT_READY(nand) udelay(10) - /*---------------------------------------------------------------------------- * SMSC9115 Ethernet from SMSC9118 family *---------------------------------------------------------------------------- */ #if defined(CONFIG_CMD_NET) -#define CONFIG_DRIVER_SMC911X -#define CONFIG_DRIVER_SMC911X_32_BIT -#define CONFIG_DRIVER_SMC911X_BASE 0x2C000000 +#define CONFIG_NET_MULTI +#define CONFIG_SMC911X +#define CONFIG_SMC911X_32_BIT +#define CONFIG_SMC911X_BASE 0x2C000000 #endif /* (CONFIG_CMD_NET) */