X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fomap3_beagle.h;h=657780edcffcf74bc6960fdb48bd7fd92fbf1f7f;hb=ba662f8998f67b31d88bf3a78970ad8375e5644a;hp=d280451a69a49a811e31dfcba76637a833eae189;hpb=0997561de956783ef1ac2f0acf649a0793882a3a;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index d280451..657780e 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -110,9 +110,6 @@ #define STATUS_LED_BOOT STATUS_LED_BIT #define STATUS_LED_GREEN STATUS_LED_BIT1 -/* DDR - I use Micron DDR */ -#define CONFIG_OMAP3_MICRON_DDR 1 - /* Enable Multi Bus support for I2C */ #define CONFIG_I2C_MULTI_BUS 1 @@ -132,6 +129,14 @@ /* USB EHCI */ #define CONFIG_CMD_USB #define CONFIG_USB_EHCI + +#define CONFIG_USB_EHCI_OMAP +/*#define CONFIG_EHCI_DCACHE*/ /* leave it disabled for now */ +#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147 + +#define CONFIG_USB_ULPI +#define CONFIG_USB_ULPI_VIEWPORT_OMAP + #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_SMSC95XX @@ -141,6 +146,8 @@ /* commands to include */ #include +#define CONFIG_CMD_ASKENV + #define CONFIG_CMD_CACHE #define CONFIG_CMD_EXT2 /* EXT2 Support */ #define CONFIG_CMD_FAT /* FAT support */ @@ -162,6 +169,7 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_SETEXPR /* Evaluate expressions */ +#define CONFIG_CMD_GPIO /* Enable gpio command */ #undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ #undef CONFIG_CMD_FPGA /* FPGA configuration Support */ @@ -207,14 +215,14 @@ /* partition */ /* Environment information */ -#define CONFIG_BOOTDELAY 2 +#define CONFIG_BOOTDELAY 3 #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x80200000\0" \ "rdaddr=0x81000000\0" \ "usbtty=cdc_acm\0" \ "bootfile=uImage.beagle\0" \ - "console=tty02,115200n8\0" \ + "console=ttyO2,115200n8\0" \ "mpurate=auto\0" \ "buddy=none "\ "optargs=\0" \ @@ -275,10 +283,16 @@ "ramboot=echo Booting from ramdisk ...; " \ "run ramargs; " \ "bootm ${loadaddr}\0" \ - + "userbutton=if gpio input 173; then run userbutton_xm; " \ + "else run userbutton_nonxm; fi;\0" \ + "userbutton_xm=gpio input 4;\0" \ + "userbutton_nonxm=gpio input 7;\0" +/* "run userbutton" will return 1 (false) if is pressed and 0 (false) if not */ #define CONFIG_BOOTCOMMAND \ "if mmc rescan ${mmcdev}; then " \ - "if userbutton; then " \ + "if run userbutton; then " \ + "setenv bootenv uEnv.txt;" \ + "else " \ "setenv bootenv user.txt;" \ "fi;" \ "echo SD/MMC found on device ${mmcdev};" \ @@ -302,7 +316,6 @@ */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #define CONFIG_SYS_PROMPT "OMAP3 beagleboard.org # " #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ /* Print Buffer Size */ @@ -336,17 +349,12 @@ * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */ -#ifdef CONFIG_USE_IRQ -#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */ -#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */ -#endif /*----------------------------------------------------------------------- * Physical Memory Map */ #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */ #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 /*----------------------------------------------------------------------- @@ -388,4 +396,56 @@ #define CONFIG_SYS_CACHELINE_SIZE 64 +/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_NAND_SIMPLE +#define CONFIG_SPL_TEXT_BASE 0x40200800 +#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ +#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK + +#define CONFIG_SPL_BSS_START_ADDR 0x80000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ + +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" + +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_SPL_OMAP3_ID_NAND +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" + +/* NAND boot config */ +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 +#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ + 10, 11, 12, 13} +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +/* + * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM + * 64 bytes before this address should be set aside for u-boot.img's + * header. That is 0x800FFFC0--0x80100000 should not be used for any + * other needs. + */ +#define CONFIG_SYS_TEXT_BASE 0x80100000 +#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 + #endif /* __CONFIG_H */