X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fmx6sxsabreauto.h;h=984cf611f4c30c6e6613d70a5663d475af25051a;hb=6d7dacf726ca043a3f5487549bbfa506c990c813;hp=0742b4bf2ec99d10ade494a0dafa94a091b573a1;hpb=e389033f72b55f1f30952e419a8505efcdd4c91d;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/mx6sxsabreauto.h b/include/configs/mx6sxsabreauto.h
index 0742b4b..984cf61 100644
--- a/include/configs/mx6sxsabreauto.h
+++ b/include/configs/mx6sxsabreauto.h
@@ -1,9 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
  *
  * Configuration settings for the Freescale i.MX6SX Sabreauto board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -95,10 +94,7 @@
 #define CONFIG_SYS_MEMTEST_START	0x80000000
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)
 
-#define CONFIG_STACKSIZE		SZ_128K
-
 /* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
 
 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
@@ -120,26 +116,17 @@
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
 #define CONFIG_SYS_I2C_SPEED		  100000
 
-/* NAND flash command */
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NAND_TRIMFFS
-
 /* NAND stuff */
-#define CONFIG_NAND_MXS
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_SYS_NAND_BASE           0x40000000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_ONFI_DETECTION
 
 /* DMA stuff, needed for GPMI/MXS NAND support */
-#define CONFIG_APBH_DMA
-#define CONFIG_APBH_DMA_BURST
-#define CONFIG_APBH_DMA_BURST8
 
 /* Network */
 
 #define CONFIG_FEC_MXC
-#define CONFIG_MII
 
 #define IMX_FEC_BASE			ENET2_BASE_ADDR
 #define CONFIG_FEC_MXC_PHYADDR          0x0
@@ -147,15 +134,8 @@
 #define CONFIG_FEC_XCV_TYPE             RGMII
 #define CONFIG_ETHPRIME                 "FEC"
 
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_ATHEROS
-
 #ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS   0
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
@@ -165,24 +145,13 @@
 
 #ifdef CONFIG_FSL_QSPI
 #define CONFIG_SYS_FSL_QSPI_AHB
-#define CONFIG_SF_DEFAULT_BUS		0
-#define CONFIG_SF_DEFAULT_CS		0
-#define CONFIG_SF_DEFAULT_SPEED	40000000
-#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
 #define FSL_QSPI_FLASH_SIZE		SZ_32M
 #define FSL_QSPI_FLASH_NUM		2
 #endif
 
-#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
-#define CONFIG_ENV_SIZE			SZ_8K
-#define CONFIG_ENV_IS_IN_MMC
-
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #if defined(CONFIG_ENV_IS_IN_MMC)
 #define CONFIG_SYS_MMC_ENV_DEV		0  /*USDHC3*/
 #endif
 
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_WIDTH	{ {0x30, 8}, {0x32, 8}, {0x34, 8} }
-
 #endif				/* __CONFIG_H */