X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fmx6sxsabreauto.h;h=058856ac866cb2afbe6577989e097011e5bfb6e7;hb=87f78478a4a1bf574db0b0e575ca37cf91fb187c;hp=9617e24614c544392a92b8e47b321f47faaa7a5f;hpb=cb04db155f4e7ccaec1b961d8a84e1a1b9524594;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/mx6sxsabreauto.h b/include/configs/mx6sxsabreauto.h
index 9617e24..058856a 100644
--- a/include/configs/mx6sxsabreauto.h
+++ b/include/configs/mx6sxsabreauto.h
@@ -1,9 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
  *
  * Configuration settings for the Freescale i.MX6SX Sabreauto board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -14,9 +13,6 @@
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
 
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
-
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART1_BASE
 
@@ -98,12 +94,8 @@
 #define CONFIG_SYS_MEMTEST_START	0x80000000
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)
 
-#define CONFIG_STACKSIZE		SZ_128K
-
 /* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
-#define PHYS_SDRAM_SIZE			SZ_2G
 
 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
 #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
@@ -118,40 +110,23 @@
 #define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC3_BASE_ADDR
 
 /* I2C Configs */
-#define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
 #define CONFIG_SYS_I2C_SPEED		  100000
 
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE100
-#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
-
-/* NAND flash command */
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NAND_TRIMFFS
-
 /* NAND stuff */
-#define CONFIG_NAND_MXS
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_SYS_NAND_BASE           0x40000000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_ONFI_DETECTION
 
 /* DMA stuff, needed for GPMI/MXS NAND support */
-#define CONFIG_APBH_DMA
-#define CONFIG_APBH_DMA_BURST
-#define CONFIG_APBH_DMA_BURST8
 
 /* Network */
-#define CONFIG_CMD_MII
 
 #define CONFIG_FEC_MXC
-#define CONFIG_MII
 
 #define IMX_FEC_BASE			ENET2_BASE_ADDR
 #define CONFIG_FEC_MXC_PHYADDR          0x0
@@ -159,16 +134,10 @@
 #define CONFIG_FEC_XCV_TYPE             RGMII
 #define CONFIG_ETHPRIME                 "FEC"
 
-#define CONFIG_PHYLIB
 #define CONFIG_PHY_ATHEROS
 
 #ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
-#define CONFIG_USB_STORAGE
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS   0
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
@@ -176,7 +145,6 @@
 
 #define CONFIG_IMX_THERMAL
 
-#define CONFIG_FSL_QSPI
 #ifdef CONFIG_FSL_QSPI
 #define CONFIG_SYS_FSL_QSPI_AHB
 #define CONFIG_SF_DEFAULT_BUS		0
@@ -189,14 +157,10 @@
 
 #define CONFIG_ENV_OFFSET		(8 * SZ_64K)
 #define CONFIG_ENV_SIZE			SZ_8K
-#define CONFIG_ENV_IS_IN_MMC
 
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #if defined(CONFIG_ENV_IS_IN_MMC)
 #define CONFIG_SYS_MMC_ENV_DEV		0  /*USDHC3*/
 #endif
 
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_WIDTH	{ {0x30, 8}, {0x32, 8}, {0x34, 8} }
-
 #endif				/* __CONFIG_H */