X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fmx6sabreauto.h;h=c76e7ea1605a4d6e855eac838f43fe6582b682dc;hb=46b5c8ed017958fc387ab86c71ae6c90abb6793c;hp=e444930dc87baa2a3d05aabcfd8aa6334a2b1b55;hpb=2738f0edea7d19960d692284d1f378b1a2b4c4a5;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/mx6sabreauto.h b/include/configs/mx6sabreauto.h
index e444930..c76e7ea 100644
--- a/include/configs/mx6sabreauto.h
+++ b/include/configs/mx6sabreauto.h
@@ -12,13 +12,10 @@
 #include "imx6_spl.h"
 #endif
 
-#define CONFIG_MACH_TYPE	3529
 #define CONFIG_MXC_UART_BASE	UART4_BASE
 #define CONSOLE_DEV		"ttymxc3"
 
 /* USB Configs */
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
 #define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS	0
 
@@ -29,49 +26,22 @@
 
 /* Falcon Mode */
 #ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SPL_FS_LOAD_ARGS_NAME	"args"
-#define CONFIG_SPL_FS_LOAD_KERNEL_NAME	"uImage"
-#define CONFIG_SYS_SPL_ARGS_ADDR       0x18000000
-
 /* Falcon Mode - MMC support: args@1MB kernel@2MB */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR  0x800   /* 1MB */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512)
-#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR        0x1000  /* 2MB */
 #endif
 
 #ifdef CONFIG_MTD_NOR_FLASH
 #define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
-#define CONFIG_SYS_FLASH_SECT_SIZE      (128 * 1024)
-#define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256   /* max number of sectors on one chip */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
 #endif
 
 #define CONFIG_SYS_FSL_USDHC_NUM	2
-#if defined(CONFIG_ENV_IS_IN_MMC)
-#define CONFIG_SYS_MMC_ENV_DEV		0
-#endif
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
-#define CONFIG_SYS_I2C_SPEED		100000
 
 /* NAND stuff */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_SYS_NAND_BASE           0x40000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_ONFI_DETECTION
 
 /* DMA stuff, needed for GPMI/MXS NAND support */
 
 /* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
 #define CONFIG_POWER_PFUZE100
 #define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08