X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fmpc5121ads.h;h=7919320c88685f29e0828fb1741793c773685bcf;hb=a1dc980d88a5c9c2b99251c8d8299b0c8948de73;hp=c36141a0076a374434bea674e0b92a4507d1b028;hpb=30aaa774df39971e0f488b7661c8825a45570cd2;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h
index c36141a..7919320 100644
--- a/include/configs/mpc5121ads.h
+++ b/include/configs/mpc5121ads.h
@@ -36,7 +36,6 @@
 /* video */
 #ifdef CONFIG_FSL_DIU_FB
 #define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_IMMR + 0x2100)
-#define CONFIG_CMD_BMP
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
 #endif
@@ -49,7 +48,6 @@
 #define CONFIG_SYS_MPC512X_CLKIN	33333333	/* in Hz */
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_F		/* call board_early_init_f() */
 #define CONFIG_MISC_INIT_R
 
 #define CONFIG_SYS_IMMR		0x80000000
@@ -275,7 +273,6 @@
 #if CONFIG_PSC_CONSOLE != 3
 #error CONFIG_PSC_CONSOLE must be 3
 #endif
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
@@ -330,29 +327,12 @@
 
 #endif
 
-/* I2C */
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES	{{0,0x69}}	/* Don't probe these addrs */
-#endif
-
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
 /*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2	/* 16-bit EEPROM address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* Atmel: AT24C32A-10TQ-2.7 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* 32-Byte Page Write Mode */
-
-/*
  * Ethernet configuration
  */
 #define CONFIG_MPC512x_FEC	1
@@ -372,7 +352,6 @@
  */
 
 #if defined(CONFIG_CMD_USB)
-#define CONFIG_USB_EHCI				/* Enable EHCI Support	*/
 #define CONFIG_USB_EHCI_FSL			/* On a FSL platform	*/
 #define CONFIG_EHCI_MMIO_BIG_ENDIAN		/* With big-endian regs	*/
 #define CONFIG_EHCI_DESC_BIG_ENDIAN
@@ -399,8 +378,6 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_REGINFO
@@ -438,11 +415,6 @@
 					"mpc5121.nand:-(data)"
 
 #if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2) || defined(CONFIG_CMD_USB)
-
-#define CONFIG_DOS_PARTITION
-#define CONFIG_MAC_PARTITION
-#define CONFIG_ISO_PARTITION
-
 #define CONFIG_SUPPORT_VFAT
 
 #endif /* defined(CONFIG_CMD_IDE) */
@@ -509,8 +481,6 @@
 
 #undef  CONFIG_BOOTARGS			/* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE		115200
-
 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"