X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fmeesc.h;h=a27b36b3786a3549d39e0aed0db6b55639bf0c92;hb=22a9ea974bdf18e6adad5c4f80b1c60ef384690c;hp=c3255fad6441756ff8964d9f31bc548755866cb8;hpb=a84b655fab2bc021fdafa91d1196cf826474cdd8;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/meesc.h b/include/configs/meesc.h
index c3255fa..a27b36b 100644
--- a/include/configs/meesc.h
+++ b/include/configs/meesc.h
@@ -3,7 +3,7 @@
  * Stelian Pop <stelian.pop@leadtechdesign.com>
  * Lead Tech Design <www.leadtechdesign.com>
  *
- * (C) Copyright 2009
+ * (C) Copyright 2009-2010
  * Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
  * esd electronic system design gmbh <www.esd.eu>
  *
@@ -32,10 +32,11 @@
 #define __CONFIG_H
 
 /* Common stuff */
-#define CONFIG_SYS_HZ			1000	/* decrementer freq */
 #define CONFIG_MEESC			1	/* Board is esd MEESC */
 #define CONFIG_ARM926EJS		1	/* This is an ARM926EJS Core */
 #define CONFIG_AT91SAM9263		1	/* It's an AT91SAM9263 SoC */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	16000000/* 16.0 MHz crystal */
+#define CONFIG_SYS_HZ			1000	/* decrementer freq */
 #define CONFIG_DISPLAY_BOARDINFO	1
 #define CONFIG_DISPLAY_CPUINFO		1	/* display cpu info and speed */
 #define CONFIG_PREBOOT				/* enable preboot variable */
@@ -47,7 +48,6 @@
 #undef CONFIG_USE_IRQ				/* don't need IRQ/FIQ stuff */
 
 #define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SKIP_RELOCATE_UBOOT
 #define CONFIG_MISC_INIT_R			/* Call misc_init_r */
 
 #define CONFIG_ARCH_CPU_INIT
@@ -57,6 +57,7 @@
  */
 
 /* Console output */
+#define CONFIG_AT91_GPIO			1
 #define CONFIG_ATMEL_USART			1
 #undef CONFIG_USART0
 #undef CONFIG_USART1
@@ -79,15 +80,14 @@
  */
 #include <config_cmd_default.h>
 #undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_AUTOSCRIPT
 #undef CONFIG_CMD_FPGA
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_USB
 
 #define CONFIG_CMD_PING				1
 #define CONFIG_CMD_DHCP				1
 #define CONFIG_CMD_NAND				1
+#define CONFIG_CMD_USB				1
 
 /* LED */
 #define CONFIG_AT91_LED				1
@@ -119,9 +119,9 @@
 #define CONFIG_SYS_NAND_MASK_ALE		(1 << 21)
 /* our CLE is AD22 */
 #define CONFIG_SYS_NAND_MASK_CLE		(1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN		AT91_PIN_PD15
-#define CONFIG_SYS_NAND_READY_PIN		AT91_PIN_PA22
-
+#define CONFIG_SYS_NAND_ENABLE_PIN		AT91_PIO_PORTD, 15
+#define CONFIG_SYS_NAND_READY_PIN		AT91_PIO_PORTA, 22
+#define CONFIG_SYS_64BIT_VSPRINTF		/* needed for nand_util.c */
 #endif
 
 /* Ethernet */
@@ -131,6 +131,17 @@
 #define CONFIG_NET_RETRY_COUNT			20
 #undef CONFIG_RESET_PHY_R
 
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_OHCI_NEW			1
+#define CONFIG_DOS_PARTITION			1
+#define CONFIG_SYS_USB_OHCI_CPU_INIT		1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE		0x00a00000
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME		"at91sam9263"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
+#define CONFIG_USB_STORAGE			1
+#define CONFIG_CMD_FAT				1
+
 #define CONFIG_SYS_LOAD_ADDR			0x22000000 /* load address */
 
 #define CONFIG_SYS_MEMTEST_START		PHYS_SDRAM
@@ -170,7 +181,6 @@
  */
 #define CONFIG_SYS_MALLOC_LEN		ROUND(3 * CONFIG_ENV_SIZE + \
 					128*1024, 0x1000)
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* 128 bytes for initial data */
 
 #define CONFIG_STACKSIZE		(32 * 1024)	/* regular stack */