X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fmecp5123.h;h=17a97dfc3ae19d28e6592bef5a417cddbe584dc9;hb=2c62e313b14186d67f5bf26095f36a246cb0c3a4;hp=6c19817f86a369be561dd74f1efadc2d890fb493;hpb=c0cae2e24552d57f3e2f841ec235453413cd7389;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h
index 6c19817..17a97df 100644
--- a/include/configs/mecp5123.h
+++ b/include/configs/mecp5123.h
@@ -15,6 +15,7 @@
 #define __CONFIG_H
 
 #define CONFIG_MECP5123 1
+
 /*
  * Memory map for the MECP5123 board:
  *
@@ -34,7 +35,6 @@
 
 #define CONFIG_SYS_MPC512X_CLKIN	33333333	/* in Hz */
 
-#define CONFIG_BOARD_EARLY_INIT_F		/* call board_early_init_f() */
 #define CONFIG_MISC_INIT_R
 
 #define CONFIG_SYS_IMMR		        0x80000000
@@ -215,7 +215,6 @@
 #if CONFIG_PSC_CONSOLE != 3
 #error CONFIG_PSC_CONSOLE must be 3
 #endif
-#define CONFIG_BAUDRATE		9600	/* ... at 9600 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 
@@ -240,18 +239,7 @@
 #define SCCR2_CLOCKS_EN	(CLOCK_SCCR2_MEM_EN |	\
 			 CLOCK_SCCR2_I2C_EN)
 
-
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* I2C */
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE		0x7F	/* slave address */
 
 /*
  * IIM - IC Identification Module
@@ -259,15 +247,6 @@
 #undef CONFIG_FSL_IIM
 
 /*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2	/* 16-bit EEPROM address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* Atmel: AT24C32A-10TQ-2.7 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10	/* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5	/* 32-Byte Page Write Mode */
-#define CONFIG_SYS_EEPROM_WREN			/* Use EEPROM write protect */
-
-/*
  * Ethernet configuration
  */
 #define CONFIG_MPC512x_FEC	1
@@ -286,31 +265,14 @@
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_EEPROM		/* Store env in I2C EEPROM	*/
+#define CONFIG_ENV_IS_NOWHERE		/* Store env in I2C EEPROM	*/
 #define CONFIG_ENV_SIZE		0x1000
 #define CONFIG_ENV_OFFSET       0x0000	/* environment starts here	*/
 
 #define CONFIG_LOADS_ECHO		/* echo on for serial download	*/
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change	*/
 
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DATE
-#undef CONFIG_CMD_FUSE
-#undef CONFIG_CMD_IDE
-#undef CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_ELF
-#define CONFIG_DOS_PARTITION
 
 /*
  * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
@@ -376,7 +338,6 @@
 
 #define CONFIG_LOADADDR		400000	/* def. location for tftp and bootm */
 
-#define CONFIG_BOOTDELAY	5	/* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS			/* the boot command will set bootargs*/
 
 #define CONFIG_PREBOOT	"echo;"	\
@@ -429,9 +390,6 @@
 
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-
 #define OF_CPU			"PowerPC,5121@0"
 #define OF_SOC_COMPAT		"fsl,mpc5121-immr"
 #define OF_TBCLK		(bd->bi_busfreq / 4)