X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fmcu25.h;h=5f311988368d115e8b97b9454cd1cfe7b91738dd;hb=3df4f46f3209c067dcadc969ed02d27c97fa3632;hp=9a83f083a8a85118abe3fcc07f7e7f40bd656ac1;hpb=0e8d158664a913392cb01fb11a948d83f72e105e;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/mcu25.h b/include/configs/mcu25.h index 9a83f08..5f31198 100644 --- a/include/configs/mcu25.h +++ b/include/configs/mcu25.h @@ -35,6 +35,12 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_405GP 1 #define CONFIG_4xx 1 +#define CONFIG_HOSTNAME mcu25 + +/* + * Include common defines/options for all boards produced by Netstal Maschinen + */ +#include "netstal-common.h" #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ @@ -45,46 +51,44 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ +#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xfff80000 /* start of FLASH */ -#define CFG_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* ... with on-chip memory here (4KBytes) */ -#define CFG_OCM_DATA_ADDR 0xF4000000 -#define CFG_OCM_DATA_SIZE 0x00001000 +#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000 /* Do not set up locked dcache as init ram. */ -#undef CFG_INIT_DCACHE_CS +#undef CONFIG_SYS_INIT_DCACHE_CS /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */ -#define CFG_TEMP_STACK_OCM 1 +#define CONFIG_SYS_TEMP_STACK_OCM 1 -#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* OCM */ -#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* OCM */ +#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ /* - * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CFG_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. + * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. + * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. + * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. * The Linux BASE_BAUD define should match this configuration. * baseBaud = cpuClock/(uartDivisor*16) - * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock, + * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ -#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ -#define CONFIG_SERIAL_MULTI 1 /* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */ -#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CFG_BASE_BAUD 691200 +#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CONFIG_SYS_BASE_BAUD 691200 /* Size (bytes) of interrupt driven serial port buffer. * Set to 0 to use polling instead of interrupts. @@ -95,27 +99,23 @@ /* Set console baudrate to 9600 */ #define CONFIG_BAUDRATE 9600 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Flash *----------------------------------------------------------------------*/ /* Use common CFI driver */ -#define CFG_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI #define CONFIG_FLASH_CFI_DRIVER /* board provides its own flash_init code */ #define CONFIG_FLASH_CFI_LEGACY 1 -#define CFG_FLASH_CFI_WIDTH FLASH_CFI_8BIT -#define CFG_FLASH_LEGACY_512Kx8 1 +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT +#define CONFIG_SYS_FLASH_LEGACY_512Kx8 1 /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ /*----------------------------------------------------------------------- * Environment @@ -135,7 +135,7 @@ #ifdef CONFIG_ENV_IS_IN_FLASH /* Put the environment in Flash */ #define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */ /* Address and size of Redundant Environment Sector */ @@ -147,77 +147,15 @@ * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the * the first internal I2C controller of the PPC440EPx *----------------------------------------------------------------------*/ -#define CFG_SPD_BUS_NUM 0 - -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F - -/* This is the 7bit address of the device, not including P. */ -#define CFG_I2C_EEPROM_ADDR 0x50 -#define CFG_I2C_EEPROM_ADDR_LEN 1 - -/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ -#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CFG_EEPROM_PAGE_WRITE_BITS 4 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#undef CFG_I2C_MULTI_EEPROMS - - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS +#define CONFIG_SYS_SPD_BUS_NUM 0 /* Setup some board specific values for the default environment variables */ -#define CONFIG_HOSTNAME mcu25 -#define CONFIG_IPADDR 172.25.1.99 -#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE -#define CONFIG_SERVERIP 172.25.1.3 - -#define CFG_TFTP_LOADADDR 0x01000000 /* @16 MB */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "loadaddr=0x01000000\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/home/diagnose/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/mcu25/uImage\0" \ - "load=tftp 100000 mcu25/u-boot.bin\0" \ - "update=protect off FFFB0000 FFFFFFFF;era FFFB0000 FFFFFFFF;" \ - "cp.b 100000 FFFB0000 50000\0" \ - "upd=run load;run update\0" \ - "vx_rom=mcu25/mcu25_vx_rom\0" \ - "vx=tftp ${loadaddr} ${vx_rom};run vxargs; bootvx\0" \ - "vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}" \ - " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \ - "" -#define CONFIG_BOOTCOMMAND "run vx" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address */ +#define CONFIG_IPADDR 172.25.1.25 -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ - -#define CONFIG_HAS_ETH0 -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descr */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_NETSTAL_DEF_ENV \ + CONFIG_NETSTAL_DEF_ENV_POWERPC \ + "" /* * BOOTP options @@ -253,100 +191,93 @@ #define SPD_EEPROM_ADDRESS 0x50 /* POST support */ -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_CPU | \ - CFG_POST_UART | \ - CFG_POST_I2C | \ - CFG_POST_CACHE | \ - CFG_POST_ETHER | \ - CFG_POST_SPR) - -#define CFG_POST_UART_TABLE {UART0_BASE} -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_UART | \ + CONFIG_SYS_POST_I2C | \ + CONFIG_SYS_POST_CACHE | \ + CONFIG_SYS_POST_ETHER | \ + CONFIG_SYS_POST_SPR) + +#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE} +#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) #undef CONFIG_LOGBUFFER -#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */ -#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ +#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ /*----------------------------------------------------------------------- * Miscellaneous configurable options *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ -#define CFG_EBC_CFG 0x98400000 +#define CONFIG_SYS_EBC_CFG 0x98400000 /* Memory Bank 0 (Flash Bank 0) initialization */ -#define CFG_EBC_PB0AP 0x02005400 -#define CFG_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit*/ +#define CONFIG_SYS_EBC_PB0AP 0x02005400 +#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit*/ -#define CFG_EBC_PB1AP 0x03041200 -#define CFG_EBC_PB1CR 0x7009A000 /* BAS=,BS=MB,BU=R/W,BW=bit */ +#define CONFIG_SYS_EBC_PB1AP 0x03041200 +#define CONFIG_SYS_EBC_PB1CR 0x7009A000 /* BAS=,BS=MB,BU=R/W,BW=bit */ -#define CFG_EBC_PB2AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */ -#define CFG_EBC_PB2CR 0x7A09A000u +#define CONFIG_SYS_EBC_PB2AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */ +#define CONFIG_SYS_EBC_PB2CR 0x7A09A000u -#define CFG_EBC_PB3AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */ -#define CFG_EBC_PB3CR 0x7B09A000u +#define CONFIG_SYS_EBC_PB3AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */ +#define CONFIG_SYS_EBC_PB3CR 0x7B09A000u -#define CFG_EBC_PB4AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */ -#define CFG_EBC_PB4CR 0x7C09A000u +#define CONFIG_SYS_EBC_PB4AP 0x01845200u /* BAS=,BS=MB,BU=R/W,BW=bit */ +#define CONFIG_SYS_EBC_PB4CR 0x7C09A000u -#define CFG_EBC_PB5AP 0x00800200u -#define CFG_EBC_PB5CR 0x7D81A000u +#define CONFIG_SYS_EBC_PB5AP 0x00800200u +#define CONFIG_SYS_EBC_PB5CR 0x7D81A000u -#define CFG_EBC_PB6AP 0x01040200u -#define CFG_EBC_PB6CR 0x7D91A000u +#define CONFIG_SYS_EBC_PB6AP 0x01040200u +#define CONFIG_SYS_EBC_PB6CR 0x7D91A000u -#define CFG_GPIO0_OR 0x087FFFFF /* GPIO value */ -#define CFG_GPIO0_TCR 0x7FFF8000 /* GPIO value */ -#define CFG_GPIO0_ODR 0xFFFF0000 /* GPIO value */ +#define CONFIG_SYS_GPIO0_OR 0x087FFFFF /* GPIO value */ +#define CONFIG_SYS_GPIO0_TCR 0x7FFF8000 /* GPIO value */ +#define CONFIG_SYS_GPIO0_ODR 0xFFFF0000 /* GPIO value */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* Init Memory Controller: * * BR0/1 and OR0/1 (FLASH) */ -#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ +#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ #define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ /* Configuration Port location */ #define CONFIG_PORT_ADDR 0xF0000500 -#define CFG_HUSH_PARSER /* use "hush" command parser */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif #if defined(CONFIG_CMD_KGDB) @@ -354,8 +285,4 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */