X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fmccmon6.h;h=69ca7c527534b5bed27638b90679fe75134cb02b;hb=6cc04547cb3bbd3a3d78947f200acbae19e3c67f;hp=a1774c027a955823c5d9026864b39f18bf8e0a8b;hpb=d32519ac8a4483803975b5aa4ef4f5affe1964bc;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/mccmon6.h b/include/configs/mccmon6.h
index a1774c0..69ca7c5 100644
--- a/include/configs/mccmon6.h
+++ b/include/configs/mccmon6.h
@@ -9,85 +9,42 @@
 
 #include "mx6_common.h"
 
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
 #include "imx6_spl.h"
 
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + 0x80000)
-#define CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + 0x180000)
-#define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + 0x1980000)
-#define CONFIG_SYS_FDT_SIZE (48 * SZ_1K)
-#define CONFIG_SYS_SPL_ARGS_ADDR	0x18000000
 
 /*
  * Below defines are set but NOT really used since we by
  * design force U-Boot run when we boot in development
  * mode from SD card (SD2)
  */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR (0x800)
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (0x80)
-#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR (0x1000)
-#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
-#define CONFIG_SPL_FS_LOAD_ARGS_NAME "imx6q-mccmon.dtb"
 
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
-
-#define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART1_BASE
 
-#define CONFIG_SYS_MEMTEST_START	0x10000000
-#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_SPEED		100000
-
 /* MMC Configuration */
-#define CONFIG_SYS_FSL_USDHC_NUM	2
-#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CFG_SYS_FSL_USDHC_NUM	2
+#define CFG_SYS_FSL_ESDHC_ADDR	0
 
 /* NOR 16-bit mode */
 #define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-#define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_FLASH_VERIFY
 
 /* NOR Flash MTD */
-#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ (CONFIG_SYS_FLASH_BASE) }
 #define CONFIG_SYS_FLASH_BANKS_SIZES	{ (32 * SZ_1M) }
 
-/* MTD support */
-
-/* USB Configs */
-#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
-#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS		0
-
 /* Ethernet Configuration */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE			ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE		RGMII
-#define CONFIG_ETHPRIME			"FEC"
 #define CONFIG_FEC_MXC_PHYADDR		1
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"console=ttymxc0,115200 quiet\0" \
-	"fdtfile=imx6q-mccmon6.dtb\0" \
 	"fdt_high=0xffffffff\0" \
 	"initrd_high=0xffffffff\0" \
 	"boot_os=yes\0" \
+	"kernelsize=0x300000\0" \
+	"disable_giga=yes\0" \
 	"download_kernel=" \
-		"tftpboot ${kernel_addr} ${kernel_file};" \
-		"tftpboot ${fdt_addr} ${fdtfile};\0" \
+		"tftpboot ${loadaddr} ${kernel_file};\0" \
 	"get_boot_medium=" \
 		"setenv boot_medium nor;" \
 		"setexpr.l _src_sbmr1 *0x020d8004;" \
@@ -95,10 +52,7 @@
 		"if test ${_b_medium} = 40; then " \
 			"setenv boot_medium sdcard;" \
 		"fi\0" \
-	"kernel_file=uImage\0" \
-	"load_kernel=" \
-		"load mmc ${bootdev}:${bootpart} ${kernel_addr} uImage;" \
-		"load mmc ${bootdev}:${bootpart} ${fdt_addr} ${fdtfile};\0" \
+	"kernel_file=fitImage\0" \
 	"boot_sd=" \
 		"echo '#######################';" \
 		"echo '# Factory SDcard Boot #';" \
@@ -109,12 +63,11 @@
 		"run factory_flash_img;\0" \
 	"boot_nor=" \
 		"setenv kernelnor 0x08180000;" \
-		"setenv dtbnor 0x09980000;" \
 		"setenv bootargs console=${console} " \
 		CONFIG_MTDPARTS_DEFAULT " " \
 		"root=/dev/mmcblk1 rootfstype=ext4 rw rootwait noinitrd;" \
-		"cp.l ${dtbnor} ${dtbloadaddr} 0x8000;" \
-		"bootm ${kernelnor} - ${dtbloadaddr};\0" \
+		"cp.l ${kernelnor} ${loadaddr} ${kernelsize};" \
+		"bootm ${loadaddr};reset;\0" \
 	"boot_recovery=" \
 		"echo '#######################';" \
 		"echo '# RECOVERY SWU Boot   #';" \
@@ -122,14 +75,13 @@
 		"setenv rootfsloadaddr 0x13000000;" \
 		"setenv swukernelnor 0x08980000;" \
 		"setenv swurootfsnor 0x09180000;" \
-		"setenv swudtbnor 0x099A0000;" \
 		"setenv bootargs console=${console} " \
 		CONFIG_MTDPARTS_DEFAULT " " \
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
 		    ":${hostname}::off root=/dev/ram rw;" \
 		"cp.l ${swurootfsnor} ${rootfsloadaddr} 0x200000;" \
-		"cp.l ${swudtbnor} ${dtbloadaddr} 0x8000;" \
-		"bootm ${swukernelnor} ${rootfsloadaddr} ${dtbloadaddr};\0" \
+		"cp.l ${swukernelnor} ${loadaddr} ${kernelsize};" \
+		"bootm ${loadaddr} ${rootfsloadaddr};reset;\0" \
 	"boot_tftp=" \
 		"echo '#######################';" \
 		"echo '# TFTP Boot           #';" \
@@ -137,7 +89,7 @@
 		"if run download_kernel; then " \
 		     "setenv bootargs console=${console} " \
 		     "root=/dev/mmcblk0p2 rootwait;" \
-		     "bootm ${kernel_addr} - ${fdt_addr};" \
+		     "bootm $loadaddr};reset;" \
 		"fi\0" \
 	"bootcmd=" \
 		"if test -n ${recovery_status}; then " \
@@ -156,14 +108,10 @@
 			  "fi;" \
 		     "fi;" \
 		"fi\0" \
-	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
-	"fdt_addr=0x18000000\0" \
 	"bootdev=1\0" \
 	"bootpart=1\0" \
-	"kernel_addr=" __stringify(CONFIG_LOADADDR) "\0" \
 	"netdev=eth0\0" \
 	"load_addr=0x11000000\0" \
-	"dtbloadaddr=0x12000000\0" \
 	"uboot_file=u-boot.img\0" \
 	"SPL_file=SPL\0" \
 	"load_uboot=tftp ${load_addr} ${uboot_file}\0" \
@@ -190,6 +138,7 @@
 		    "device ${mmcdev};" \
 		    "run factory_nor_img;" \
 		    "run factory_eMMC_img;" \
+		    "run factory_SPL_falcon_setup;" \
 		"fi\0" \
 	"factory_eMMC_img="\
 		"echo 'Update mccmon6 eMMC image'; " \
@@ -211,6 +160,16 @@
 		    "erase ${nor_bank_start} +${nor_img_size};" \
 		    "setexpr nor_img_size ${nor_img_size} / 4; " \
 		    "cp.l ${nor_img_addr} ${nor_bank_start} ${nor_img_size}\0" \
+	"factory_SPL_falcon_setup="\
+		"echo 'Write Falcon boot data'; " \
+		"setenv kernelnor 0x08180000;" \
+		"cp.l ${kernelnor} ${loadaddr} ${kernelsize};" \
+		"spl export fdt ${loadaddr};" \
+		"setenv nor_img_addr ${fdtargsaddr};" \
+		"setenv nor_img_size 0x20000;" \
+		"setenv nor_bank_start " \
+				__stringify(CONFIG_CMD_SPL_NOR_OFS)";" \
+		"run nor_update\0" \
 	"tftp_nor_uboot="\
 		"echo 'Update mccmon6 NOR U-BOOT via TFTP'; " \
 		"setenv nor_img_file u-boot.img; " \
@@ -219,22 +178,14 @@
 		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
 		    "run nor_update;" \
 		"fi\0" \
-	"tftp_nor_uImg="\
-		"echo 'Update mccmon6 NOR uImage via TFTP'; " \
-		"setenv nor_img_file uImage; " \
+	"tftp_nor_fitImg="\
+		"echo 'Update mccmon6 NOR fitImage via TFTP'; " \
+		"setenv nor_img_file fitImage; " \
 		"setenv nor_img_size 0x500000; " \
 		"setenv nor_bank_start 0x08180000; " \
 		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
 		    "run nor_update;" \
 		"fi\0" \
-	"tftp_nor_dtb="\
-		"echo 'Update mccmon6 NOR DTB via TFTP'; " \
-		"setenv nor_img_file imx6q-mccmon6.dtb; " \
-		"setenv nor_img_size 0x20000; " \
-		"setenv nor_bank_start 0x09980000; " \
-		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
-		    "run nor_update;" \
-		"fi\0" \
 	"tftp_nor_img="\
 		"echo 'Update mccmon6 NOR image via TFTP'; " \
 		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
@@ -269,20 +220,8 @@
 #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
 
-#define CONFIG_SYS_INIT_SP_OFFSET \
-	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
-	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
 /* Environment organization */
-#define CONFIG_ENV_SIZE			(SZ_128K)
 
 /* Envs are stored in NOR flash */
-#define CONFIG_ENV_SECT_SIZE    (SZ_128K)
-#define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + 0x40000)
-
-#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_SYS_FLASH_BASE + 0x60000)
-#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
 
 #endif			       /* __CONFIG_H * */