X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Flx2160ardb.h;h=ebe5004f440929d0039cbfcc14eaffb9a1be4749;hb=92832045c54586e9dffa082ff8cd8c2ef6040757;hp=f54edf356a2271ac4b7fd4a12ed92d3caa22019b;hpb=224899d273e1426cc18be317744be2c03798c41f;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/lx2160ardb.h b/include/configs/lx2160ardb.h
index f54edf3..ebe5004 100644
--- a/include/configs/lx2160ardb.h
+++ b/include/configs/lx2160ardb.h
@@ -8,47 +8,9 @@
 
 #include "lx2160a_common.h"
 
-/* Qixis */
-#define QIXIS_XMAP_MASK			0x07
-#define QIXIS_XMAP_SHIFT		5
-#define QIXIS_RST_CTL_RESET_EN		0x30
-#define QIXIS_LBMAP_DFLTBANK		0x00
-#define QIXIS_LBMAP_ALTBANK		0x20
-#define QIXIS_LBMAP_QSPI		0x00
-#define QIXIS_RCW_SRC_QSPI		0xff
-#define QIXIS_RST_CTL_RESET		0x31
-#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
-#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
-#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
-#define QIXIS_LBMAP_MASK		0x0f
-#define QIXIS_LBMAP_SD
-#define QIXIS_LBMAP_EMMC
-#define QIXIS_RCW_SRC_SD           0x08
-#define QIXIS_RCW_SRC_EMMC         0x09
-#define NON_EXTENDED_DUTCFG
-
 /* VID */
-
-#define I2C_MUX_CH_VOL_MONITOR		0xA
-/* Voltage monitor on channel 2*/
-#define I2C_VOL_MONITOR_ADDR		0x63
-#define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2
-#define I2C_VOL_MONITOR_BUS_V_OVF	0x1
-#define I2C_VOL_MONITOR_BUS_V_SHIFT	3
 #define CONFIG_VID_FLS_ENV		"lx2160ardb_vdd_mv"
 #define CONFIG_VID
-
-/* The lowest and highest voltage allowed*/
-#define VDD_MV_MIN			775
-#define VDD_MV_MAX			855
-
-/* PM Bus commands code for LTC3882*/
-#define PMBUS_CMD_PAGE                  0x0
-#define PMBUS_CMD_READ_VOUT             0x8B
-#define PMBUS_CMD_PAGE_PLUS_WRITE       0x05
-#define PMBUS_CMD_VOUT_COMMAND          0x21
-#define PWM_CHANNEL0                    0x0
-
 #define CONFIG_VOL_MONITOR_LTC3882_SET
 #define CONFIG_VOL_MONITOR_LTC3882_READ
 
@@ -59,18 +21,6 @@
 #if defined(CONFIG_FSL_MC_ENET)
 #define CONFIG_MII
 #define CONFIG_ETHPRIME		"DPMAC1@xgmii"
-
-#define AQR107_PHY_ADDR1	0x04
-#define AQR107_PHY_ADDR2	0x05
-#define AQR107_IRQ_MASK		0x0C
-
-#define CORTINA_NO_FW_UPLOAD
-#define CORTINA_PHY_ADDR1	0x0
-#define INPHI_PHY_ADDR1		0x0
-
-#define RGMII_PHY_ADDR1		0x01
-#define RGMII_PHY_ADDR2		0x02
-
 #endif
 
 /* EMC2305 */
@@ -80,13 +30,8 @@
 #define I2C_EMC2305_PWM		0x80
 
 /* EEPROM */
-#define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM	           0
-#define CONFIG_SYS_I2C_EEPROM_ADDR	           0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	    1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS     3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 
 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS		\
@@ -101,7 +46,7 @@
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 		" bootm $load_addr#$BOARD\0"			\
 	"sd_bootcmd=echo Trying load from sd card..;"		\
-		"mmcinfo; mmc read $load_addr "			\
+		"mmc dev 0; mmcinfo; mmc read $load_addr "			\
 		"$kernel_addr_sd $kernel_size_sd ;"		\
 		"env exists secureboot && mmc read $kernelheader_addr_r "\
 		"$kernelhdr_addr_sd $kernelhdr_size_sd "	\