X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Flx2160a_common.h;h=8b2b7479c11bec2bfd4cb1610c4856101705c727;hb=6cc04547cb3bbd3a3d78947f200acbae19e3c67f;hp=e31f8d087f716bdf0562436f97f30802370aa2f0;hpb=859703251251d9567f29ab10c0a29f98eb0aff5c;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h
index e31f8d0..8b2b747 100644
--- a/include/configs/lx2160a_common.h
+++ b/include/configs/lx2160a_common.h
@@ -10,18 +10,13 @@
 #include <asm/arch/config.h>
 #include <asm/arch/soc.h>
 
-#define CONFIG_FSL_MEMAC
-
-#define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_FLASH_BASE		0x20000000
 
 /* DDR */
-#define CONFIG_SYS_FSL_DDR_INTLV_256B	/* force 256 byte interleaving */
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE		0x80000000UL
-#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
+#define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CONFIG_SYS_DDR_BLOCK2_BASE		0x2080000000ULL
-#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS	2
 #define CONFIG_SYS_SDRAM_SIZE			0x200000000UL
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
@@ -32,10 +27,6 @@
 #define SPD_EEPROM_ADDRESS5		0x55
 #define SPD_EEPROM_ADDRESS6		0x56
 #define SPD_EEPROM_ADDRESS		SPD_EEPROM_ADDRESS1
-#define CONFIG_SYS_SPD_BUS_NUM		0	/* SPD on I2C bus 0 */
-#define CONFIG_DIMM_SLOTS_PER_CTLR	2
-#define CONFIG_CHIP_SELECTS_PER_CTRL	4
-#define CONFIG_SYS_MONITOR_LEN		(936 * 1024)
 
 /* Miscellaneous configurable options */
 
@@ -48,7 +39,6 @@
  * will be udpated later when get_bus_freq(0) is available.
  */
 
-#define COUNTER_FREQUENCY		25000000	/* 25MHz */
 
 /* Serial Port */
 #define CONFIG_PL011_CLOCK		(get_bus_freq(0) / 4)
@@ -69,11 +59,6 @@
 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET	0x00F20000
 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS	5000
 
-/* Define phy_reset function to boot the MC based on mcinitcmd.
- * This happens late enough to properly fixup u-boot env MAC addresses.
- */
-#define CONFIG_RESET_PHY_R
-
 /*
  * Carve out a DDR region which will not be used by u-boot/Linux
  *
@@ -92,48 +77,16 @@
 #define RTC
 #define CONFIG_SYS_I2C_RTC_ADDR		0x51  /* Channel 3*/
 
-/* EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM		0
-
 /* Qixis */
-#define CONFIG_FSL_QIXIS
-#define CONFIG_QIXIS_I2C_ACCESS
 #define CONFIG_SYS_I2C_FPGA_ADDR		0x66
 
-/* PCI */
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#endif
-
-/* SATA */
-
-#ifdef CONFIG_SCSI
-#define CONFIG_SYS_SATA1		AHCI_BASE_ADDR1
-#define CONFIG_SYS_SATA2		AHCI_BASE_ADDR2
-#endif
-
 /* USB */
-#ifdef CONFIG_USB_HOST
-#ifndef CONFIG_TARGET_LX2162AQDS
-#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
-#endif
-#endif
 
 #define COUNTER_FREQUENCY_REAL		(get_board_sys_clk() / 4)
 
 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE		128
 
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
-					sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */
-#define CONFIG_SYS_MAXARGS		64	/* max command args */
-
-#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
-
 /* Initial environment variables */
 #define XSPI_MC_INIT_CMD				\
 	"sf probe 0:0 && "				\
@@ -174,7 +127,6 @@
 	"ramdisk_size=0x2000000\0"		\
 	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
-	"fdt_addr=0x64f00000\0"			\
 	"kernel_start=0x1000000\0"		\
 	"kernelheader_start=0x600000\0"		\
 	"scriptaddr=0x80000000\0"		\
@@ -244,12 +196,36 @@
 		"run distro_bootcmd;run sd2_bootcmd;"		\
 		"env exists secureboot && esbc_halt;"
 
+#ifdef CONFIG_CMD_USB
+#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
+#else
+#define BOOT_TARGET_DEVICES_USB(func)
+#endif
+
+#ifdef CONFIG_MMC
+#define BOOT_TARGET_DEVICES_MMC(func, instance) func(MMC, mmc, instance)
+#else
+#define BOOT_TARGET_DEVICES_MMC(func)
+#endif
+
+#ifdef CONFIG_SCSI
+#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
+#else
+#define BOOT_TARGET_DEVICES_SCSI(func)
+#endif
+
+#ifdef CONFIG_CMD_DHCP
+#define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
+#else
+#define BOOT_TARGET_DEVICES_DHCP(func)
+#endif
+
 #define BOOT_TARGET_DEVICES(func) \
-	func(USB, usb, 0) \
-	func(MMC, mmc, 0) \
-	func(MMC, mmc, 1) \
-	func(SCSI, scsi, 0) \
-	func(DHCP, dhcp, na)
+	BOOT_TARGET_DEVICES_USB(func) \
+	BOOT_TARGET_DEVICES_MMC(func, 0) \
+	BOOT_TARGET_DEVICES_MMC(func, 1) \
+	BOOT_TARGET_DEVICES_SCSI(func) \
+	BOOT_TARGET_DEVICES_DHCP(func)
 #include <config_distro_bootcmd.h>
 
 #endif /* __LX2_COMMON_H */