X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fluan.h;h=cba7295fe97219dbee6ef8de3e87fea685f196a4;hb=feaa43f3a8f465cbf01ffa1b23b6b52431819a52;hp=9c8769b200bf65b82b87d48aee4371bfb0fd11d6;hpb=fc1e45ce6e45d5d88a42f4245b2d7ee134270029;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/luan.h b/include/configs/luan.h
index 9c8769b..cba7295 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -39,7 +39,6 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
@@ -135,7 +134,7 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
 #define SPD_EEPROM_ADDRESS	{0x53, 0x52}	/* SPD i2c spd addresses*/
-#undef CONFIG_DDR_ECC			/* no ECC support for now	*/
+#define CONFIG_DDR_ECC		1	/* with ECC support		*/
 
 /*-----------------------------------------------------------------------
  * I2C
@@ -212,31 +211,38 @@
 #define CONFIG_HW_WATCHDOG			/* watchdog */
 #endif
 
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL		|	\
-				CFG_CMD_ASKENV		|	\
-				CFG_CMD_DHCP		|	\
-				CFG_CMD_ELF		|	\
-				CFG_CMD_EEPROM		|	\
-				CFG_CMD_I2C		|	\
-				CFG_CMD_IRQ		|	\
-				CFG_CMD_MII		|	\
-				CFG_CMD_NET		|	\
-				CFG_CMD_NFS		|	\
-				CFG_CMD_PCI		|	\
-				CFG_CMD_PING		|	\
-				CFG_CMD_REGINFO		|	\
-				CFG_CMD_SDRAM		|	\
-				0)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
 
 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
@@ -264,7 +270,7 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#if (CONFIG_COMMANDS & CFG_CMD_PCI)
+#if defined(CONFIG_CMD_PCI)
 
 /* General PCI */
 #define CONFIG_PCI			/* include pci support	        */
@@ -272,14 +278,13 @@
 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
 
 /* Board-specific PCI */
-#define CFG_PCI_PRE_INIT                /* enable board pci_pre_init()  */
 #define CFG_PCI_TARGET_INIT
 #undef  CFG_PCI_MASTER_INIT
 
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_DEVICEID 0x4403	/* whatever */
 
-#endif /* CONFIG_COMMANDS & CFG_CMD_PCI */
+#endif
 
 /*
  * For booting Linux, the board info and command line data
@@ -288,15 +293,6 @@
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		(32<<10) /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
@@ -305,7 +301,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif