X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fluan.h;h=41999d32f97aaa2142080c1bbf7886e97349d3d2;hb=3c1de1a6d36be9eee284a6c596a86e94f19cc5b2;hp=cbb59c50eaf3a8c605f51910b8dcd12f8653df36;hpb=98c440bee623ecdd5322852732b883e696fb2140;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/luan.h b/include/configs/luan.h
index cbb59c5..41999d3 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -39,7 +39,6 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
@@ -69,7 +68,6 @@
 #define CFG_FLASH_BASE		CFG_SMALL_FLASH
 #endif
 
-#undef CFG_DRAM_TEST
 #if CFG_SRAM_BASE
 #define CFG_KBYTES_SDRAM	1024*2
 #else
@@ -136,7 +134,6 @@
 #define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
 #define SPD_EEPROM_ADDRESS	{0x53, 0x52}	/* SPD i2c spd addresses*/
 #define CONFIG_DDR_ECC		1	/* with ECC support		*/
-#define CFG_44x_DDR2_CKTR_180	1	/* use 180 deg advance		*/
 
 /*-----------------------------------------------------------------------
  * I2C
@@ -154,7 +151,7 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
 #define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"
 
 #undef	CONFIG_BOOTARGS
@@ -184,7 +181,7 @@
 	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
 		"cp.b 100000 fffc0000 40000;"			        \
 		"setenv filesize;saveenv\0"				\
-	"upd=run load;run update\0"					\
+	"upd=run load update\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -197,6 +194,7 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+#define CONFIG_HAS_ETH0
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1
 #define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
@@ -213,31 +211,38 @@
 #define CONFIG_HW_WATCHDOG			/* watchdog */
 #endif
 
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL		|	\
-				CFG_CMD_ASKENV		|	\
-				CFG_CMD_DHCP		|	\
-				CFG_CMD_ELF		|	\
-				CFG_CMD_EEPROM		|	\
-				CFG_CMD_I2C		|	\
-				CFG_CMD_IRQ		|	\
-				CFG_CMD_MII		|	\
-				CFG_CMD_NET		|	\
-				CFG_CMD_NFS		|	\
-				CFG_CMD_PCI		|	\
-				CFG_CMD_PING		|	\
-				CFG_CMD_REGINFO		|	\
-				CFG_CMD_SDRAM		|	\
-				0)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
 
 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
@@ -265,7 +270,7 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#if (CONFIG_COMMANDS & CFG_CMD_PCI)
+#if defined(CONFIG_CMD_PCI)
 
 /* General PCI */
 #define CONFIG_PCI			/* include pci support	        */
@@ -279,7 +284,7 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_DEVICEID 0x4403	/* whatever */
 
-#endif /* CONFIG_COMMANDS & CFG_CMD_PCI */
+#endif
 
 /*
  * For booting Linux, the board info and command line data
@@ -288,15 +293,6 @@
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		(32<<10) /* For AMCC 440 CPUs			*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*
  * Internal Definitions
  *
@@ -305,9 +301,13 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
 #endif	/* __CONFIG_H */