X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fls1088ardb.h;h=4cb5d7517f3dc627a382c1dd1a253c5145c75491;hb=0f9595b9fa68ed1634adddf989fd037909eec433;hp=fd2e508537284c305d3426dc79caa337f816af8f;hpb=d7d40f614d5e6b6c7369ebd001d3ac191b3e360b;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/ls1088ardb.h b/include/configs/ls1088ardb.h
index fd2e508..4cb5d75 100644
--- a/include/configs/ls1088ardb.h
+++ b/include/configs/ls1088ardb.h
@@ -16,19 +16,12 @@
 #define SYS_NO_FLASH
 #endif
 
-#define CONFIG_SYS_CLK_FREQ		100000000
-#define CONFIG_DDR_CLK_FREQ		100000000
 #define COUNTER_FREQUENCY_REAL		25000000	/* 25MHz */
 #define COUNTER_FREQUENCY		25000000	/* 25MHz */
 
-#define CONFIG_DDR_SPD
 #ifdef CONFIG_EMU
 #define CONFIG_SYS_FSL_DDR_EMU
-#define CONFIG_SYS_MXC_I2C1_SPEED	40000000
-#define CONFIG_SYS_MXC_I2C2_SPEED	40000000
 #else
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif
 #define SPD_EEPROM_ADDRESS	0x51
@@ -67,7 +60,6 @@
 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
 
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
@@ -77,10 +69,6 @@
 #endif
 #endif
 
-#ifndef SPL_NO_IFC
-#define CONFIG_NAND_FSL_IFC
-#endif
-
 #define CONFIG_SYS_NAND_MAX_ECCPOS	256
 #define CONFIG_SYS_NAND_MAX_OOBFREE	2
 
@@ -99,8 +87,6 @@
 				| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
 				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
 
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
 /* ONFI NAND Flash mode0 Timing Params */
 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
 					FTIM0_NAND_TWP(0x18)   | \
@@ -119,8 +105,6 @@
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_MTD_NAND_VERIFY_WRITE
 
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-
 #ifndef SPL_NO_QIXIS
 #define CONFIG_FSL_QIXIS
 #endif
@@ -211,16 +195,10 @@
 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
 #define I2C_SVDD_MONITOR_ADDR		0x4F
 
-#define CONFIG_VID_FLS_ENV              "ls1088ardb_vdd_mv"
-#define CONFIG_VID
-
 /* The lowest and highest voltage allowed for LS1088ARDB */
 #define VDD_MV_MIN			819
 #define VDD_MV_MAX			1212
 
-#define CONFIG_VOL_MONITOR_LTC3882_SET
-#define CONFIG_VOL_MONITOR_LTC3882_READ
-
 #define PWM_CHANNEL0                    0x0
 
 /*
@@ -243,10 +221,6 @@
 /* EEPROM */
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM		0
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
 
 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
@@ -442,7 +416,6 @@
 		"bootm $load_addr#$BOARD\0"
 #endif /* CONFIG_TFABOOT */
 
-#undef CONFIG_BOOTCOMMAND
 #ifdef CONFIG_TFABOOT
 #define QSPI_NOR_BOOTCOMMAND					\
 	"sf read 0x80001000 0xd00000 0x100000;"		\
@@ -464,26 +437,8 @@
 #else
 #if defined(CONFIG_QSPI_BOOT)
 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
-#define CONFIG_BOOTCOMMAND                                      \
-		"sf read 0x80001000 0xd00000 0x100000;"		\
-		"env exists mcinitcmd && env exists secureboot "	\
-		" && sf read 0x806C0000 0x6C0000 0x100000 "	\
-		"&& esbc_validate 0x806C0000;env exists mcinitcmd "	\
-		"&& fsl_mc lazyapply dpl 0x80001000;"		\
-		"run distro_bootcmd;run qspi_bootcmd;"		\
-		"env exists secureboot && esbc_halt;"
 
 /* Try to boot an on-SD kernel first, then do normal distro boot */
-#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_BOOTCOMMAND                                      \
-		"env exists mcinitcmd && mmcinfo; "		\
-		"mmc read 0x80001000 0x6800 0x800; "		\
-		"env exists mcinitcmd && env exists secureboot "	\
-		" && mmc read 0x806C0000 0x3600 0x20 "		\
-		"&& esbc_validate 0x806C0000;env exists mcinitcmd "	\
-		"&& fsl_mc lazyapply dpl 0x80001000;"		\
-		"run distro_bootcmd;run sd_bootcmd;"		\
-		"env exists secureboot && esbc_halt;"
 #endif
 #endif /* CONFIG_TFABOOT */
 
@@ -502,7 +457,6 @@
 #define QSGMII2_PORT4_PHY_ADDR		0x1f
 
 #define CONFIG_ETHPRIME		"DPMAC1@xgmii"
-#define CONFIG_PHY_GIGE
 #endif
 #endif