X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fkorat.h;h=46335b4b7f7977d8f62e417d95ebe1f3f0def4f5;hb=544aa66a6695790227613bf32bdf672143d5a1ad;hp=026dd0854aca4f01014eebd85c87c926ada044f9;hpb=35e3717772c8c3534c18d8aac69e4b822777c23b;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/korat.h b/include/configs/korat.h
index 026dd08..46335b4 100644
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -38,6 +38,12 @@
 #define CONFIG_4xx		1	/* ... PPC4xx family		*/
 #define CONFIG_SYS_CLK_FREQ	33333333
 
+#ifdef CONFIG_KORAT_PERMANENT
+#define CONFIG_SYS_TEXT_BASE	0xFFFA0000
+#else
+#define	CONFIG_SYS_TEXT_BASE	0xF7F60000
+#endif
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 #define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
 
@@ -64,16 +70,13 @@
 #define CONFIG_SYS_FLASH1_MAX_SIZE	0x08000000
 #define CONFIG_SYS_FLASH1_ADDR		(CONFIG_SYS_FLASH1_TOP - CONFIG_SYS_FLASH1_MAX_SIZE)
 #define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_FLASH1_ADDR	/* start of FLASH	*/
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_OCM_BASE		0xe0010000	/* ocm			*/
 #define CONFIG_SYS_OCM_DATA_ADDR	CONFIG_SYS_OCM_BASE
 #define CONFIG_SYS_PCI_BASE		0xe0000000	/* Internal PCI regs	*/
 #define CONFIG_SYS_PCI_MEMBASE		0x80000000	/* mapped pci memory	*/
 #define CONFIG_SYS_PCI_MEMBASE2		(CONFIG_SYS_PCI_MEMBASE + 0x20000000)
 
-/* Don't change either of these */
-#define CONFIG_SYS_PERIPHERAL_BASE	0xef600000	/* internal peripherals	*/
-
 #define CONFIG_SYS_USB2D0_BASE		0xe0000100
 #define CONFIG_SYS_USB_DEVICE		0xe0000000
 #define CONFIG_SYS_USB_HOST		0xe0000400
@@ -85,19 +88,21 @@
 /* 440EPx has 16KB of internal SRAM, so no need for D-Cache		*/
 #undef CONFIG_SYS_INIT_RAM_DCACHE
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_BASE	/* OCM			*/
-#define CONFIG_SYS_INIT_RAM_END	(4 << 10)
-#define CONFIG_SYS_GBL_DATA_SIZE	256	/* num bytes initial data	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	(4 << 10)
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 
 /*
  * Serial Port
  */
+#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
 #define CONFIG_SYS_EXT_SERIAL_CLOCK	11059200	/* ext. 11.059MHz clk	*/
 #define CONFIG_BAUDRATE		115200
 #define CONFIG_SERIAL_MULTI	1
-/* define this if you want console on UART1 */
-#undef CONFIG_UART1_CONSOLE
 
 #define CONFIG_SYS_BAUDRATE_TABLE						\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
@@ -153,6 +158,7 @@
  */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
@@ -244,7 +250,6 @@
 #define CONFIG_HAS_ETH0
 #define CONFIG_SYS_RX_ETH_BUFFER	32	/* Number of ethernet rx	*/
 					/*   buffers & descriptors	*/
-#define CONFIG_NET_MULTI	1
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
 #define CONFIG_PHY1_ADDR	3
 
@@ -305,7 +310,6 @@
 				 CONFIG_SYS_POST_SPR	| \
 				 CONFIG_SYS_POST_UART)
 
-#define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 #define CONFIG_LOGBUFFER
 #define CONFIG_SYS_POST_CACHE_ADDR	0xC8000000	/* free virtual address     */
 
@@ -552,14 +556,6 @@
 }											\
 }
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02	/* Software reboot			*/
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400 /* speed to run kgdb serial port	*/
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use	*/