X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fkm%2Fkm_arm.h;h=7dff0f4bf38af225f7d99153642bd89d6eb86863;hb=55dabcc8f24598e2777f663de09ab55fbe1269da;hp=79edfa728a54e3471e405ca8972f5f55d234ccc5;hpb=60c7facfc965af6ff8ea14ee26c9d49cd2d0ec22;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h
index 79edfa7..7dff0f4 100644
--- a/include/configs/km/km_arm.h
+++ b/include/configs/km/km_arm.h
@@ -35,6 +35,9 @@
 /* Reserve 4 MB for malloc */
 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
 
+/* Increase max size of compressed kernel */
+#define CONFIG_SYS_BOOTM_LEN		(32 << 20)
+
 #include "asm/arch/config.h"
 
 #define CONFIG_SYS_LOAD_ADDR	0x00800000	/* default load adr- 8M */
@@ -45,7 +48,7 @@
 		" boardid=0x${IVM_BoardId} hwkey=0x${IVM_HWKey}"
 
 #define CONFIG_KM_DEF_ENV_CPU						\
-	"u-boot="CONFIG_HOSTNAME "/u-boot.kwb\0"		\
+	"u-boot=" CONFIG_HOSTNAME "/u-boot.kwb\0"		\
 	CONFIG_KM_UPDATE_UBOOT						\
 	"set_fdthigh=setenv fdt_high ${kernelmem}\0"			\
 	"checkfdt="							\
@@ -87,8 +90,6 @@
  * I2C related stuff
  */
 #undef CONFIG_I2C_MVTWSI
-#define CONFIG_SYS_I2C
-#define	CONFIG_SYS_I2C_SOFT	/* I2C bit-banged	*/
 #define CONFIG_SYS_I2C_INIT_BOARD
 
 #define	CONFIG_KIRKWOOD_GPIO		/* Enable GPIO Support */
@@ -107,10 +108,6 @@
 #include <linux/delay.h>
 #include <linux/stringify.h>
 extern void __set_direction(unsigned pin, int high);
-void set_sda(int state);
-void set_scl(int state);
-int get_sda(void);
-int get_scl(void);
 #define KM_KIRKWOOD_SDA_PIN	8
 #define KM_KIRKWOOD_SCL_PIN	9
 #define KM_KIRKWOOD_SOFT_I2C_GPIOS	0x0300
@@ -126,16 +123,8 @@ int get_scl(void);
 #define I2C_DELAY	udelay(1)
 #define I2C_SOFT_DECLARATIONS
 
-#define	CONFIG_SYS_I2C_SOFT_SLAVE	0x0
-#define	CONFIG_SYS_I2C_SOFT_SPEED	100000
-
 /* EEprom support 24C128, 24C256 valid for environment eeprom */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6 /* 64 Byte write page */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
 
 /*
  *  Environment variables configurations
@@ -143,8 +132,6 @@ int get_scl(void);
 #if defined CONFIG_KM_ENV_IS_IN_SPI_NOR
 #define CONFIG_ENV_TOTAL_SIZE		0x20000     /* no bracets! */
 #else
-#define CONFIG_SYS_DEF_EEPROM_ADDR	0x50
-#define CONFIG_ENV_EEPROM_IS_ON_I2C
 #define CONFIG_SYS_EEPROM_WREN
 #define CONFIG_I2C_ENV_EEPROM_BUS 5 /* I2C2 (Mux-Port 5) */
 #endif
@@ -166,9 +153,9 @@ int get_scl(void);
 	"newenv=setenv addr 0x100000 && "				\
 		"i2c dev " __stringify(CONFIG_I2C_ENV_EEPROM_BUS) "; "  \
 		"mw.b ${addr} 0 4 && "					\
-		"eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR)	\
+		"eeprom write " __stringify(CONFIG_SYS_I2C_EEPROM_ADDR)	\
 		" ${addr} " __stringify(CONFIG_ENV_OFFSET) " 4 && "	\
-		"eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR)	\
+		"eeprom write " __stringify(CONFIG_SYS_I2C_EEPROM_ADDR)	\
 		" ${addr} " __stringify(CONFIG_ENV_OFFSET_REDUND) " 4\0"
 #endif