X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fkm%2Fkm_arm.h;h=7dff0f4bf38af225f7d99153642bd89d6eb86863;hb=55dabcc8f24598e2777f663de09ab55fbe1269da;hp=0de83f6723c5126c599453bff8196b4ea2e271d9;hpb=93e72ac472b537bb4b0c6a97a7e6aab2b37860c6;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index 0de83f6..7dff0f4 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -32,42 +32,23 @@ /* include common defines/options for all Keymile boards */ #include "keymile-common.h" -/* SPI NOR Flash default params, used by sf commands */ -#define CONFIG_SF_DEFAULT_SPEED 8100000 -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 - -#if defined CONFIG_KM_ENV_IS_IN_SPI_NOR -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 8100000 -#define CONFIG_ENV_SPI_MODE SPI_MODE_3 -#endif - /* Reserve 4 MB for malloc */ #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) +/* Increase max size of compressed kernel */ +#define CONFIG_SYS_BOOTM_LEN (32 << 20) + #include "asm/arch/config.h" -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ #define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -/* pseudo-non volatile RAM [hex] */ -#define CONFIG_KM_PNVRAM 0x80000 -/* physical RAM MTD size [hex] */ -#define CONFIG_KM_PHRAM 0x17F000 - -#define CONFIG_KM_CRAMFS_ADDR 0x2400000 -#define CONFIG_KM_KERNEL_ADDR 0x2000000 /* 3098KBytes */ -#define CONFIG_KM_FDT_ADDR 0x23E0000 /* 128KBytes */ - /* architecture specific default bootargs */ #define CONFIG_KM_DEF_BOOT_ARGS_CPU \ "bootcountaddr=${bootcountaddr} ${mtdparts}" \ " boardid=0x${IVM_BoardId} hwkey=0x${IVM_HWKey}" #define CONFIG_KM_DEF_ENV_CPU \ - "u-boot="CONFIG_HOSTNAME "/u-boot.kwb\0" \ + "u-boot=" CONFIG_HOSTNAME "/u-boot.kwb\0" \ CONFIG_KM_UPDATE_UBOOT \ "set_fdthigh=setenv fdt_high ${kernelmem}\0" \ "checkfdt=" \ @@ -81,26 +62,10 @@ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ /* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE -#define CONFIG_SYS_NS16550_COM2 KW_UART1_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -/* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_BOOTMAPSZ (8 << 20) /* Initial Memmap for Linux */ #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ #define CONFIG_INITRD_TAG /* enable INITRD tag */ #define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */ @@ -110,37 +75,21 @@ */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define BOOTFLASH_START 0x0 - -/* Kirkwood has two serial IF */ -#if (CONFIG_CONS_INDEX == 2) -#define CONFIG_KM_CONSOLE_TTY "ttyS1" -#else -#define CONFIG_KM_CONSOLE_TTY "ttyS0" -#endif - /* * Other required minimal configurations */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ /* * Ethernet Driver configuration */ -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ +#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer autoneg timeout */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_KM_COMMON_ETH_INIT /* standard km ethernet_present for piggy */ /* * I2C related stuff */ #undef CONFIG_I2C_MVTWSI -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ #define CONFIG_SYS_I2C_INIT_BOARD #define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */ @@ -156,11 +105,9 @@ #ifndef __ASSEMBLY__ #include +#include +#include extern void __set_direction(unsigned pin, int high); -void set_sda(int state); -void set_scl(int state); -int get_sda(void); -int get_scl(void); #define KM_KIRKWOOD_SDA_PIN 8 #define KM_KIRKWOOD_SCL_PIN 9 #define KM_KIRKWOOD_SOFT_I2C_GPIOS 0x0300 @@ -176,45 +123,19 @@ int get_scl(void); #define I2C_DELAY udelay(1) #define I2C_SOFT_DECLARATIONS -#define CONFIG_SYS_I2C_SOFT_SLAVE 0x0 -#define CONFIG_SYS_I2C_SOFT_SPEED 100000 - /* EEprom support 24C128, 24C256 valid for environment eeprom */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 Byte write page */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* * Environment variables configurations */ #if defined CONFIG_KM_ENV_IS_IN_SPI_NOR -#define CONFIG_ENV_OFFSET 0xc0000 /* no bracets! */ -#define CONFIG_ENV_SIZE 0x02000 /* Size of Environment */ -#define CONFIG_ENV_SECT_SIZE 0x10000 -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_TOTAL_SIZE 0x20000 /* no bracets! */ #else -#define CONFIG_SYS_DEF_EEPROM_ADDR 0x50 -#define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_EEPROM_WREN -#define CONFIG_ENV_OFFSET 0x0 /* no bracets! */ -#define CONFIG_ENV_SIZE (0x2000 - CONFIG_ENV_OFFSET) #define CONFIG_I2C_ENV_EEPROM_BUS 5 /* I2C2 (Mux-Port 5) */ -#define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */ -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #endif -#define CONFIG_SYS_REDUNDAND_ENVIRONMENT - - -/* SPI bus claim MPP configuration */ -#define CONFIG_SYS_KW_SPI_MPP 0x0 - -#define FLASH_GPIO_PIN 0x00010000 #define KM_FLASH_GPIO_PIN 16 #define CONFIG_KM_UPDATE_UBOOT \ @@ -232,9 +153,9 @@ int get_scl(void); "newenv=setenv addr 0x100000 && " \ "i2c dev " __stringify(CONFIG_I2C_ENV_EEPROM_BUS) "; " \ "mw.b ${addr} 0 4 && " \ - "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \ + "eeprom write " __stringify(CONFIG_SYS_I2C_EEPROM_ADDR) \ " ${addr} " __stringify(CONFIG_ENV_OFFSET) " 4 && " \ - "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \ + "eeprom write " __stringify(CONFIG_SYS_I2C_EEPROM_ADDR) \ " ${addr} " __stringify(CONFIG_ENV_OFFSET_REDUND) " 4\0" #endif @@ -252,19 +173,9 @@ int get_scl(void); "arch=arm\0" \ "" -#if !defined(CONFIG_MTD_NOR_FLASH) -#undef CONFIG_JFFS2_CMDLINE -#endif - /* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 -/* Do early setups now in board_init_f() */ -/* - * resereved pram area at the end of memroy [hex] - * 8Mbytes for switch + 4Kbytes for bootcount - */ -#define CONFIG_KM_RESERVED_PRAM 0x801000 /* address for the bootcount (taken from end of RAM) */ #define BOOTCOUNT_ADDR (CONFIG_KM_RESERVED_PRAM) @@ -273,6 +184,4 @@ int get_scl(void); #define CONFIG_POST_SKIP_ENV_FLAGS #define CONFIG_POST_EXTERNAL_WORD_FUNCS -/* we do the whole PCIe FPGA config stuff here */ - #endif /* _CONFIG_KM_ARM_H */