X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fkatmai.h;h=b0dc175afed2ad5360bdd1d691e3c0566230f6ea;hb=abbb90666d5ef2f500ebbedbb80ff60adc56b043;hp=78c794a05de0b3e79eaad0368d9d5ebed06bd9aa;hpb=2eb6e01049886bdaadf11243e7c8cf674c34ed0b;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 78c794a..b0dc175 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -37,23 +37,30 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_440SPE 1 /* Specifc SPe support */ -#undef CFG_DRAM_TEST /* Disable-takes long time */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ + +/* + * Enable this board for more than 2GB of SDRAM + */ +#define CONFIG_PHYS_64BIT +#define CONFIG_VERY_BIG_RAM +#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)2 << 30) + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME katmai +#include "amcc-common.h" #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ #undef CONFIG_SHOW_BOOT_PROGRESS /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */ - -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xff000000 /* start of FLASH */ -#define CFG_MONITOR_BASE TEXT_BASE #define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ @@ -98,12 +105,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE #undef CFG_EXT_SERIAL_CLOCK -#define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * DDR SDRAM @@ -117,10 +120,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE @@ -132,7 +132,6 @@ #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0x50) #define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_ENABLE #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 @@ -170,143 +169,44 @@ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ -#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS +#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=katmai\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "net_nfs_fdt=tftp 200000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty;" \ - "bootm 200000 - ${fdt_addr}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=katmai/uImage\0" \ - "fdt_file=katmai/katmai.dtb\0" \ - "fdt_addr=400000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff10000\0" \ "ramdisk_addr=fff20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 katmai/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b ${fileaddr} fffc0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ "kozio=bootm ffc60000\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP #define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_HAS_ETH0 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ #define CFG_FLASH_CFI -#define CFG_FLASH_CFI_DRIVER +#define CONFIG_FLASH_CFI_DRIVER #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ @@ -318,13 +218,13 @@ #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) /*----------------------------------------------------------------------- * PCI stuff @@ -432,28 +332,4 @@ #define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF) #define CFG_GPIO_ODR 0 -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */