X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fipek01.h;h=ece72c6aa1d267b7789ed9a3978575030df9a82e;hb=4125bbcef6a998ce8580a1f5c53c8c93a56a125b;hp=230f2c4d3090dea6f9fee6a097e7ec8898fcf98a;hpb=808bf7cf655a1caa5f48f6f3a6b274f4b83ab8b4;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h
index 230f2c4..ece72c6 100644
--- a/include/configs/ipek01.h
+++ b/include/configs/ipek01.h
@@ -35,7 +35,6 @@
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
-#define CONFIG_BAUDRATE		115200	/* ... at 9600 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history */
@@ -43,18 +42,12 @@
 /*
  * Video configuration for LIME GDC
  */
-#define CONFIG_VIDEO
 #ifdef CONFIG_VIDEO
 #define CONFIG_VIDEO_MB862xx
 #define CONFIG_VIDEO_MB862xx_ACCEL
 #define VIDEO_FB_16BPP_WORD_SWAP
-#define CONFIG_CFB_CONSOLE
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_VIDEO_SW_CURSOR
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_VIDEO_BMP_GZIP
 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE	(2 << 20)	/* decompressed img */
@@ -69,8 +62,6 @@
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */
-#define CONFIG_PCI		1
-#define CONFIG_PCI_PNP		1
 #define CONFIG_PCI_SCAN_SHOW	1
 
 #define CONFIG_PCI_MEM_BUS	0x40000000
@@ -85,13 +76,9 @@
 #define CONFIG_EEPRO100		1
 #define CONFIG_SYS_RX_ETH_BUFFER	8  /* use 8 rx buffer on eepro100  */
 
-/* Partitions */
-#define CONFIG_DOS_PARTITION
-
 /* USB */
 #define CONFIG_USB_OHCI_NEW
 #define CONFIG_SYS_OHCI_BE_CONTROLLER
-#define CONFIG_USB_STORAGE
 
 #define CONFIG_SYS_USB_OHCI_CPU_INIT
 #define CONFIG_SYS_USB_OHCI_REGS_BASE		MPC5XXX_USB
@@ -101,25 +88,15 @@
 /*
  * Command line configuration.
  */
-#ifdef CONFIG_VIDEO
-#define CONFIG_CMD_BMP		/* BMP support */
-#endif
-#define CONFIG_CMD_DATE		/* support for RTC, date/time...*/
-#define CONFIG_CMD_DHCP		/* DHCP Support */
-#define CONFIG_CMD_FAT		/* FAT support */
-#define CONFIG_CMD_I2C		/* I2C serial bus support */
 #define CONFIG_CMD_IDE		/* IDE harddisk support */
 #define CONFIG_CMD_IRQ		/* irqinfo */
-#define CONFIG_CMD_MII		/* MII support */
 #define CONFIG_CMD_PCI		/* pciinfo */
-#define CONFIG_CMD_USB		/* USB Support */
 
 #define CONFIG_SYS_LOWBOOT	1
 
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
 
 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
@@ -169,36 +146,10 @@
 /*
  * Open firmware flat tree support
  */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
 
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE	2	/* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED	100000	/* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE	0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x53
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR		0x51
-
 #define CONFIG_SYS_FLASH_BASE		0xFC000000
 #define CONFIG_SYS_FLASH_SIZE		0x01000000
 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + \
@@ -293,8 +244,6 @@
 
 #define CONFIG_SYS_LOAD_ADDR		0x100000 /* default load address */
 
-#define CONFIG_LOOPW
-
 /*
  * Various low-level settings
  */