X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Finnokom.h;h=f9535c9840d3ba26e1c26b35057a89cdc89a60aa;hb=225f0eaa745adfae05931848543d99942798756a;hp=cfe9032893d1f3676580dad94aa56d471e2ec009;hpb=8bde7f776c77b343aca29b8c7b58464d915ac245;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/innokom.h b/include/configs/innokom.h
index cfe9032..f9535c9 100644
--- a/include/configs/innokom.h
+++ b/include/configs/innokom.h
@@ -31,16 +31,10 @@
 #define __CONFIG_H
 
 /*
- * If we are developing, we might want to start U-Boot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#define CONFIG_INIT_CRITICAL		/* undef for developing */
-
-/*
  * High Level Configuration Options
  * (easy to change)
  */
-#define CONFIG_PXA250 		1	/* This is an PXA250 CPU            */
+#define CONFIG_PXA250		1	/* This is an PXA250 CPU            */
 #define CONFIG_INNOKOM		1	/* on an Auerswald Innokom board    */
 
 #undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff      */
@@ -60,10 +54,34 @@
 #define CONFIG_BAUDRATE		19200
 #define CONFIG_MISC_INIT_R	1	/* we have a misc_init_r() function */
 
-#define CONFIG_COMMANDS (CFG_CMD_BDI|CFG_CMD_LOADB|CFG_CMD_IMI|CFG_CMD_FLASH|CFG_CMD_MEMORY|CFG_CMD_NET|CFG_CMD_ENV|CFG_CMD_RUN|CFG_CMD_ASKENV|CFG_CMD_ECHO|CFG_CMD_I2C|CFG_CMD_DHCP|CFG_CMD_CACHE)
-/* CONFIG_CMD_DFL|CFG_CMD_I2C|CFG_CMD_EEPROM|CFG_CMD_NET|CFG_CMD_JFFS2|CFG_CMD_DHCP) */
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any)   */
-#include <cmd_confdefs.h>
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_RUN
+
 
 #define CONFIG_BOOTDELAY	3
 /* #define CONFIG_BOOTARGS	"root=/dev/nfs ip=bootp console=ttyS0,19200" */
@@ -82,11 +100,10 @@
  */
 
 /*
- * Size of malloc() pool; this lives below the uppermost 128 KiB which are
- * used for the RAM copy of the uboot code
- *
+ * Size of malloc() pool
  */
 #define CFG_MALLOC_LEN		(256*1024)
+#define CFG_GBL_DATA_SIZE	128		/* size in bytes reserved for initial data */
 
 #define CFG_LONGHELP				/* undef to save memory         */
 #define CFG_PROMPT		"uboot> "	/* Monitor Command Prompt       */
@@ -119,14 +136,14 @@
 /*
  * I2C bus
  */
-#define CONFIG_HARD_I2C 		1
-#define CFG_I2C_SPEED 			50000
-#define CFG_I2C_SLAVE 			0xfe
+#define CONFIG_HARD_I2C			1
+#define CFG_I2C_SPEED			50000
+#define CFG_I2C_SLAVE			0xfe
 
-#define CFG_ENV_IS_IN_EEPROM 		1
+#define CONFIG_ENV_IS_IN_EEPROM		1
 
-#define CFG_ENV_OFFSET			0x00	/* environment starts here  */
-#define CFG_ENV_SIZE			1024	/* 1 KiB                    */
+#define CONFIG_ENV_OFFSET			0x00	/* environment starts here  */
+#define CONFIG_ENV_SIZE			1024	/* 1 KiB                    */
 #define CFG_I2C_EEPROM_ADDR		0x50	/* A0 = 0 (hardwired)       */
 #define CFG_EEPROM_PAGE_WRITE_BITS	5	/* 5 bits = 32 octets       */
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	15	/* between stop and start   */
@@ -141,6 +158,7 @@
 #define CONFIG_SMC91111_BASE		0x14000000 /* chip select 5         */
 #undef  CONFIG_SMC_USE_32_BIT		           /* 16 bit bus access     */
 #undef  CONFIG_SMC_91111_EXT_PHY		   /* we use internal phy   */
+#define CONFIG_SMC_AUTONEG_TIMEOUT	10	   /* timeout 10 seconds    */
 #undef  CONFIG_SHOW_ACTIVITY
 #define CONFIG_NET_RETRY_COUNT		10	   /* # of retries          */
 
@@ -170,14 +188,42 @@
 
 #define CFG_FLASH_BASE          PHYS_FLASH_1
 
-
 /*
- * JFFS2 Partitions
+ * JFFS2 partitions
+ *
  */
-#define CFG_JFFS_CUSTOM_PART	1		/* see board/innokom/flash.c */
-#define CONFIG_MTD_INNOKOM_16MB 1		/* development flash         */
-#undef  CONFIG_MTD_INNOKOM_64MB			/* production flash          */
+/* development flash */
+#define CONFIG_MTD_INNOKOM_16MB	1
+#undef CONFIG_MTD_INNOKOM_64MB
+
+/* production flash */
+/*
+#define CONFIG_MTD_INNOKOM_64MB	1
+#undef CONFIG_MTD_INNOKOM_16MB
+*/
 
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV		"nor0"
+#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET	0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=innokom-0"
+*/
+
+/* development flash */
+/*
+#define MTDPARTS_DEFAULT	"mtdparts=innokom-0:256k(uboot),768k(kernel),8m(user),7m(data)"
+*/
+
+/* production flash */
+/*
+#define MTDPARTS_DEFAULT	"mtdparts=innokom-0:256k(uboot),768k(kernel),16256k(user1),16256k(user2),32m(data)"
+*/
 
 /*
  * GPIO settings