X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Finnokom.h;h=744d65c6e4d6e898c6402311d3d8c0128951d00a;hb=f38536f9138c253b0c1f9c72093a7ec6808e638f;hp=45e22bfc4902b059a6f5db16b778520f42852f8a;hpb=7511835b29f2074ebfa8ea794f0303ec8e49542b;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/innokom.h b/include/configs/innokom.h
index 45e22bf..744d65c 100644
--- a/include/configs/innokom.h
+++ b/include/configs/innokom.h
@@ -39,6 +39,12 @@
 
 #undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff      */
 					/* for timer/console/ethernet       */
+
+#define	CONFIG_SYS_TEXT_BASE	0x0
+
+/* we will never enable dcache, because we have to setup MMU first */
+#define CONFIG_SYS_NO_DCACHE
+
 /*
  * Hardware drivers
  */
@@ -46,6 +52,7 @@
 /*
  * select serial console configuration
  */
+#define CONFIG_PXA_SERIAL
 #define CONFIG_FFUART		1	/* we use FFUART on CSB226 */
 
 /* allow to overwrite serial and ethaddr */
@@ -103,7 +110,6 @@
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN		(256*1024)
-#define CONFIG_SYS_GBL_DATA_SIZE	128		/* size in bytes reserved for initial data */
 
 #define CONFIG_SYS_LONGHELP				/* undef to save memory         */
 #define CONFIG_SYS_PROMPT		"uboot> "	/* Monitor Command Prompt       */
@@ -115,11 +121,9 @@
 #define CONFIG_SYS_MEMTEST_START	0xa0400000      /* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END         0xa0800000      /* 4 ... 8 MB in DRAM   */
 
-#undef  CONFIG_SYS_CLKS_IN_HZ          /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR           0xa3000000      /* load kernel to this address   */
 
-#define CONFIG_SYS_HZ                  3686400         /* incrementer freq: 3.6864 MHz */
+#define CONFIG_SYS_HZ			1000
 						/* RS: the oscillator is actually 3680130?? */
 
 #define CONFIG_SYS_CPUSPEED            0x141           /* set core clock to 200/200/100 MHz */
@@ -136,6 +140,8 @@
 /*
  * I2C bus
  */
+#define CONFIG_I2C_MV			1
+#define CONFIG_MV_I2C_REG		0x40301680
 #define CONFIG_HARD_I2C			1
 #define CONFIG_SYS_I2C_SPEED			50000
 #define CONFIG_SYS_I2C_SLAVE			0xfe
@@ -154,7 +160,8 @@
 /*
  * SMSC91C111 Network Card
  */
-#define CONFIG_DRIVER_SMC91111		1
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC91111		1
 #define CONFIG_SMC91111_BASE		0x14000000 /* chip select 5         */
 #undef  CONFIG_SMC_USE_32_BIT		           /* 16 bit bus access     */
 #undef  CONFIG_SMC_91111_EXT_PHY		   /* we use internal phy   */
@@ -188,6 +195,9 @@
 
 #define CONFIG_SYS_FLASH_BASE          PHYS_FLASH_1
 
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define	CONFIG_SYS_INIT_SP_ADDR		(GENERATED_GBL_DATA_SIZE + PHYS_SDRAM_1)
+
 /*
  * JFFS2 partitions
  *
@@ -203,7 +213,7 @@
 */
 
 /* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
 #define CONFIG_JFFS2_DEV		"nor0"
 #define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
 #define CONFIG_JFFS2_PART_OFFSET	0x00000000
@@ -211,7 +221,7 @@
 /* mtdparts command line support */
 /* Note: fake mtd_id used, no linux mtd map file */
 /*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
 #define MTDIDS_DEFAULT		"nor0=innokom-0"
 */
 
@@ -340,6 +350,9 @@
  */
 #define CONFIG_SYS_PSSR_VAL		0x37
 
+#define	CONFIG_SYS_CCCR			CCCR_L27|CCCR_M2|CCCR_N10
+#define	CONFIG_SYS_CKEN			0x0
+
 /*
  * Memory settings
  *
@@ -473,6 +486,9 @@
 #define CONFIG_SYS_MCIO0_VAL		0x00000000
 #define CONFIG_SYS_MCIO1_VAL		0x00000000
 
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
+
 /*
 #define CSB226_USER_LED0	0x00000008
 #define CSB226_USER_LED1	0x00000010