X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Finka4x0.h;h=405234cc851700aa84a781f7e0763e0b285a3386;hb=c1b7c70083fc8d0bb77db20dd47bb6c988f3dc67;hp=c817d2c3a8fdafc8075a170d6765f12927352206;hpb=f4733a0764741966a5e842968166b40fb062d577;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h index c817d2c..405234c 100644 --- a/include/configs/inka4x0.h +++ b/include/configs/inka4x0.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2003-2004 + * (C) Copyright 2003-2005 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this @@ -33,24 +33,21 @@ #define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ #define CONFIG_INKA4X0 1 /* INKA4x0 board */ -#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* * Serial console configuration */ #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } /* * PCI Mapping: @@ -60,6 +57,7 @@ #define CONFIG_PCI 1 #define CONFIG_PCI_PNP 1 #define CONFIG_PCI_SCAN_SHOW 1 +#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 #define CONFIG_PCI_MEM_BUS 0x40000000 #define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS @@ -69,117 +67,155 @@ #define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS #define CONFIG_PCI_IO_SIZE 0x01000000 -#define CFG_XLB_PIPELINING 1 +#define CONFIG_SYS_XLB_PIPELINING 1 /* Partitions */ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION #define CONFIG_ISO_PARTITION + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + /* - * Supported commands + * Command line configuration. */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_EXT2 | \ - CFG_CMD_FAT | \ - CFG_CMD_IDE | \ - CFG_CMD_PCI | \ - CFG_CMD_USB ) +#include + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_IDE +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include #define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ #if (TEXT_BASE == 0xFFE00000) /* Boot low */ -# define CFG_LOWBOOT 1 +# define CONFIG_SYS_LOWBOOT 1 #endif /* * Autobooting */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ #define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ "echo" #undef CONFIG_BOOTARGS +#define CONFIG_ETHADDR 00:a0:a4:03:00:00 +#define CONFIG_OVERWRITE_ETHADDR_ONCE + +#define CONFIG_IPADDR 192.168.100.2 +#define CONFIG_SERVERIP 192.168.100.1 +#define CONFIG_NETMASK 255.255.255.0 +#define HOSTNAME inka4x0 +#define CONFIG_BOOTFILE /tftpboot/inka4x0/uImage +#define CONFIG_ROOTPATH /opt/eldk/ppc_6xx + #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ + "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ - ":$(hostname):$(netdev):off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm $(kernel_addr)\0" \ - "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addcons=setenv bootargs ${bootargs} " \ + "console=ttyS0,${baudrate}\0" \ + "flash_nfs=run nfsargs addip addcons;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};" \ + "run nfsargs addip addcons;bootm\0" \ + "enable_disp=mw.l 100000 04000000 1;" \ + "cp.l 100000 f0000b20 1;" \ + "cp.l 100000 f0000b28 1\0" \ + "ideargs=setenv bootargs root=/dev/hda1 rw\0" \ + "ide_boot=ext2load ide 0:1 200000 uImage;" \ + "run ideargs addip addcons enable_disp;bootm\0" \ + "brightness=255\0" \ "" -#define CONFIG_BOOTCOMMAND "run net_nfs" +#define CONFIG_BOOTCOMMAND "run ide_boot" /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * Flash configuration */ -#define CFG_FLASH_BASE 0xFFE00000 - -#define CFG_FLASH_SIZE 0x00200000 /* 2 MByte */ -#define CFG_MAX_FLASH_SECT 35 /* max num of sects on one chip */ - -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000) /* second sector */ -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER 1 +#define CONFIG_SYS_FLASH_BASE 0xffe00000 +#define CONFIG_SYS_FLASH_SIZE 0x00200000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ /* * Environment settings */ -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_SIZE 0x2000 -#define CFG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ /* * Memory map */ -#define CFG_MBAR 0xF0000000 -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 -#define CONFIG_MPC5200_DDR +/* + * SDRAM controller configuration + */ +#undef CONFIG_SDR_MT48LC16M16A2 +#undef CONFIG_DDR_MT46V16M16 +#undef CONFIG_DDR_MT46V32M16 +#undef CONFIG_DDR_HYB25D512160BF +#define CONFIG_DDR_K4H511638C /* Use ON-Chip SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM #ifdef CONFIG_POST /* preserve space for the post_word at end of on-chip SRAM */ -#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE #else -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE #endif -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT 1 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 #endif -#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Ethernet configuration @@ -190,12 +226,13 @@ */ /* #define CONFIG_FEC_10MBIT 1 */ #define CONFIG_PHY_ADDR 0x00 +#define CONFIG_MII /* * GPIO configuration * - * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): - * Bit 0 (mask: 0x80000000): 1 + * use CS1 as gpio_wkup_6 output + * Bit 0 (mask: 0x80000000): 0 * use ALT CAN position: Bits 2-3 (mask: 0x30000000): * 00 -> No Alternatives, I2C1 is used for onboard EEPROM * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard @@ -203,14 +240,8 @@ * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 * use PSC6_1 and PSC6_3 as GPIO: Bits 9:11 (mask: 0x07000000): * 011 -> PSC6 could not be used as UART or CODEC. IrDA still possible. - * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST - * tests. */ -#if defined (CONFIG_MINIFAP) -#define CFG_GPS_PORT_CONFIG 0x93000004 -#else -#define CFG_GPS_PORT_CONFIG 0x81001004 -#endif +#define CONFIG_SYS_GPS_PORT_CONFIG 0x01001004 /* * RTC configuration @@ -220,30 +251,34 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ /* Enable an alternate, more extensive memory test */ -#define CFG_ALT_MEMTEST +#define CONFIG_SYS_ALT_MEMTEST -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /* - * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined, - * which is normally part of the default commands (CFV_CMD_DFL) + * Enable loopw command. */ #define CONFIG_LOOPW @@ -251,36 +286,36 @@ * Various low-level settings */ #if defined(CONFIG_MPC5200) -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE #else -#define CFG_HID0_INIT 0 -#define CFG_HID0_FINAL 0 +#define CONFIG_SYS_HID0_INIT 0 +#define CONFIG_SYS_HID0_FINAL 0 #endif -#define CFG_BOOTCS_START CFG_FLASH_BASE -#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#define CFG_BOOTCS_CFG 0x00087800 /* for pci_clk = 66 MHz */ -#define CFG_CS0_START CFG_FLASH_BASE -#define CFG_CS0_SIZE CFG_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x00087800 /* for pci_clk = 66 MHz */ +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE /* 32Mbit SRAM @0x30000000 */ -#define CFG_CS1_START 0x30000000 -#define CFG_CS1_SIZE 0x00400000 -#define CFG_CS1_CFG 0x31800 /* for pci_clk = 33 MHz */ +#define CONFIG_SYS_CS1_START 0x30000000 +#define CONFIG_SYS_CS1_SIZE 0x00400000 +#define CONFIG_SYS_CS1_CFG 0x31800 /* for pci_clk = 33 MHz */ /* 2 quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */ -#define CFG_CS2_START 0x80000000 -#define CFG_CS2_SIZE 0x0001000 -#define CFG_CS2_CFG 0x21800 /* for pci_clk = 33 MHz */ +#define CONFIG_SYS_CS2_START 0x80000000 +#define CONFIG_SYS_CS2_SIZE 0x0001000 +#define CONFIG_SYS_CS2_CFG 0x21800 /* for pci_clk = 33 MHz */ /* GPIO in @0x30400000 */ -#define CFG_CS3_START 0x30400000 -#define CFG_CS3_SIZE 0x00100000 -#define CFG_CS3_CFG 0x31800 /* for pci_clk = 33 MHz */ +#define CONFIG_SYS_CS3_START 0x30400000 +#define CONFIG_SYS_CS3_SIZE 0x00100000 +#define CONFIG_SYS_CS3_CFG 0x31800 /* for pci_clk = 33 MHz */ -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x33333333 +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 /*----------------------------------------------------------------------- * USB stuff @@ -304,25 +339,18 @@ #define CONFIG_IDE_RESET /* reset for ide supported */ #define CONFIG_IDE_PREINIT -#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CFG_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */ - -#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */ -#define CFG_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CFG_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CFG_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CFG_ATA_STRIDE 4 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0060 /* Offset for data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x005C /* Offset for alternate registers */ +#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ #define CONFIG_ATAPI 1 +#define CONFIG_SYS_BRIGHTNESS 0xFF /* LCD Default Brightness (255 = off) */ + #endif /* __CONFIG_H */