X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fidmr.h;h=fc046d60556869960a48d43a5c96f0580cc5e7fc;hb=f38536f9138c253b0c1f9c72093a7ec6808e638f;hp=b1dbe2ccb944d392aa001446a0f2d5686663145f;hpb=b78bb469f536b357ee21c54f40201dbe4b201ac3;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/idmr.h b/include/configs/idmr.h index b1dbe2c..fc046d6 100644 --- a/include/configs/idmr.h +++ b/include/configs/idmr.h @@ -44,8 +44,10 @@ */ #define CONFIG_BOOTCOMMAND "run net_nfs" #define CONFIG_BOOTDELAY 5 +#define CONFIG_MCFUART +#define CONFIG_SYS_UART_PORT (0) #define CONFIG_BAUDRATE 19200 -#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } #define CONFIG_ETHADDR 00:06:3b:01:41:55 #define CONFIG_ETHPRIME #define CONFIG_IPADDR 192.168.30.1 @@ -55,9 +57,11 @@ #define CONFIG_NETMASK 255.255.0.0 #define CONFIG_HOSTNAME idmr #define CONFIG_BOOTFILE /tftpboot/idmr/uImage -#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root " \ +#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root " \ "filesystem over NFS; echo" +#define CONFIG_MCFTMR + #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -70,7 +74,7 @@ "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=$(serverip):$(rootpath)\0" \ - "ethact=FEC ETHERNET\0" \ + "ethact=FEC\0 " \ "update=prot off ff800000 ff81ffff; era ff800000 ff81ffff; " \ "cp.b 200000 ff800000 $(filesize);" \ "prot on ff800000 ff81ffff\0" \ @@ -78,18 +82,27 @@ "u-boot=/tftpboot/idmr/u-boot.bin\0" \ "" + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + /* - * Commands' definition + * Command line configuration. */ -#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \ - CFG_CMD_PING | \ - CFG_CMD_JFFS2 | \ - CFG_CMD_NET) & \ - ~(CFG_CMD_LOADS | \ - CFG_CMD_LOADB)) +#include -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include +#define CONFIG_CMD_PING +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_NET + +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_LOADB /* @@ -102,102 +115,135 @@ * Configuration for environment, which occupies third sector in flash. */ #ifndef CONFIG_MONITOR_IS_IN_RAM -#define CFG_ENV_ADDR 0xff820000 -#define CFG_ENV_SECT_SIZE 0x10000 -#define CFG_ENV_SIZE 0x2000 -#define CFG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR 0xff820000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_IS_IN_FLASH #else /* CONFIG_MONITOR_IS_IN_RAM */ -#define CFG_ENV_OFFSET 0x4000 -#define CFG_ENV_SECT_SIZE 0x2000 -#define CFG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_IS_IN_FLASH #endif /* !CONFIG_MONITOR_IS_IN_RAM */ -#define CFG_PROMPT "=> " -#define CFG_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ + +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else /* !(CONFIG_COMMANDS & CFG_CMD_KGDB) */ -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif /* (CONFIG_COMMANDS & CFG_CMD_KGDB) */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_LOAD_ADDR 0x00100000 +#define CONFIG_SYS_LOAD_ADDR 0x00100000 -#define CFG_MEMTEST_START 0x400 -#define CFG_MEMTEST_END 0x380000 +#define CONFIG_SYS_MEMTEST_START 0x400 +#define CONFIG_SYS_MEMTEST_END 0x380000 -#define CFG_HZ (50000000 / 64) -#define CFG_CLK 100000000 +#define CONFIG_SYS_HZ (50000000 / 64) +#define CONFIG_SYS_CLK 100000000 -#define CFG_MBAR 0x40000000 /* Register Base Addrs */ +#define CONFIG_SYS_MBAR 0x40000000 /* Register Base Addrs */ /* * Ethernet */ -#define FEC_ENET -#define CONFIG_NET_RETRY_COUNT 5 -#define CFG_ENET_BD_BASE 0x480000 -#define CFG_DISCOVER_PHY 1 -#define CONFIG_MII 1 +#define CONFIG_MCFFEC +#ifdef CONFIG_MCFFEC +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 +# define CONFIG_MII_INIT 1 +# define CONFIG_SYS_DISCOVER_PHY +# define CONFIG_SYS_RX_ETH_BUFFER 8 +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN + +# define CONFIG_SYS_FEC0_PINMUX 0 +# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE +# define MCFFEC_TOUT_LOOP 50000 +/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ +# ifndef CONFIG_SYS_DISCOVER_PHY +# define FECDUPLEX FULL +# define FECSPEED _100BASET +# else +# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN +# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN +# endif +# endif /* CONFIG_SYS_DISCOVER_PHY */ +#endif /* * Definitions for initial stack pointer and data area (in DPRAM) */ -#define CFG_INIT_RAM_ADDR 0x20000000 -#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ -#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ -#define CFG_FLASH_BASE 0xff800000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CONFIG_SYS_FLASH_BASE 0xff800000 #ifdef CONFIG_MONITOR_IS_IN_RAM -#define CFG_MONITOR_BASE 0x20000 +#define CONFIG_SYS_MONITOR_BASE 0x20000 #else /* !CONFIG_MONITOR_IS_IN_RAM */ -#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) #endif /* CONFIG_MONITOR_IS_IN_RAM */ -#define CFG_MONITOR_LEN 0x20000 -#define CFG_MALLOC_LEN (256 << 10) -#define CFG_BOOTPARAMS_LEN (64*1024) +#define CONFIG_SYS_MONITOR_LEN 0x20000 +#define CONFIG_SYS_MALLOC_LEN (256 << 10) +#define CONFIG_SYS_BOOTPARAMS_LEN (64*1024) /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) /* FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 1000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 -#define CFG_FLASH_SIZE 0x800000 +#define CONFIG_SYS_FLASH_SIZE 0x800000 /* - * #define CFG_FLASH_USE_BUFFER_WRITE 1 + * #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 */ /* Cache Configuration */ -#define CFG_CACHELINE_SIZE 16 +#define CONFIG_SYS_CACHELINE_SIZE 16 + +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ + CF_CACR_DISD | CF_CACR_INVI | \ + CF_CACR_CEIB | CF_CACR_DCM | \ + CF_CACR_EUSP) /* Port configuration */ -#define CFG_FECI2C 0xF0 +#define CONFIG_SYS_FECI2C 0xF0 /* Dynamic MTD partition support */ -#define CONFIG_JFFS2_CMDLINE +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_FLASH_CFI_MTD #define MTDIDS_DEFAULT "nor0=idmr-0" #define MTDPARTS_DEFAULT "mtdparts=idmr-0:128k(u-boot)," \ @@ -206,8 +252,8 @@ "2m(rootfs)," \ "-(user)"; -#if (CONFIG_COMMANDS & CFG_CMD_MII) -#error MII commands don't work on iDMR board and sholud not be enabled. -#endif /* (CONFIG_COMMANDS & CFG_CMD_MII) */ +#if defined(CONFIG_CMD_MII) +#error "MII commands don't work on iDMR board and should not be enabled." +#endif #endif /* _IDMR_H */