X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fge_bx50v3.h;h=0eeffd46377bfa8548a3b4da326ebe04dba9a28c;hb=92832045c54586e9dffa082ff8cd8c2ef6040757;hp=73cdc5b489fb4b070065d109c0da2c25a7e9a786;hpb=9a0cbae22a613dfd55e15565785749b74c19fdf0;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h
index 73cdc5b..0eeffd4 100644
--- a/include/configs/ge_bx50v3.h
+++ b/include/configs/ge_bx50v3.h
@@ -16,20 +16,9 @@
 
 #define CONFIG_BOARD_NAME	"General Electric Bx50v3"
 
-#define CONFIG_MXC_UART_BASE	UART3_BASE
-#define CONSOLE_DEV	"ttymxc2"
-
 #include "mx6_common.h"
 #include <linux/sizes.h>
 
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)
-
-#define CONFIG_MXC_UART
-
 /* SATA Configs */
 #ifdef CONFIG_CMD_SATA
 #define CONFIG_SYS_SATA_MAX_DEVICE	1
@@ -38,35 +27,7 @@
 #define CONFIG_LBA48
 #endif
 
-/* USB Configs */
-#ifdef CONFIG_USB
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS	0
-
-#define CONFIG_USBD_HS
-#define CONFIG_USB_GADGET_MASS_STORAGE
-#endif
-
-/* Networking Configs */
-#ifdef CONFIG_NET
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE			ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE		RGMII
-#define CONFIG_ETHPRIME		"FEC"
-#define CONFIG_FEC_MXC_PHYADDR		4
-#define CONFIG_PHY_ATHEROS
-#endif
-
-/* Serial Flash */
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_LOADADDR	0x12000000
-
-#ifdef CONFIG_NFS_CMD
+#ifdef CONFIG_CMD_NFS
 #define NETWORKBOOT \
         "setnetworkboot=" \
                 "setenv ipaddr 172.16.2.10; setenv serverip 172.16.2.20; " \
@@ -74,15 +35,15 @@
                 "setenv netmask 255.255.255.0; setenv ethaddr ca:fe:de:ca:f0:11; " \
                 "setenv bootargs root=/dev/nfs nfsroot=${nfsserver}:/srv/nfs/,v3,tcp rw rootwait" \
                 "setenv bootargs $bootargs ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off " \
-                "setenv bootargs $bootargs cma=128M bootcause=POR console=${console} ${videoargs} " \
+                "setenv bootargs $bootargs cma=128M bootcause=${bootcause} ${videoargs} " \
                 "setenv bootargs $bootargs systemd.mask=helix-network-defaults.service " \
                 "setenv bootargs $bootargs watchdog.handle_boot_enabled=1\0" \
         "networkboot=" \
                 "run setnetworkboot; " \
                 "nfs ${loadaddr} /srv/nfs/fitImage; " \
-                "bootm ${loadaddr}#conf@${confidx}\0" \
+                "bootm ${loadaddr}\0" \
 
-#define CONFIG_NETWORKBOOTCOMMAND \
+#define NETWORKBOOTCOMMAND \
 	"run networkboot; " \
 
 #else
@@ -92,43 +53,35 @@
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	NETWORKBOOT \
-	"bootcause=POR\0" \
 	"image=/boot/fitImage\0" \
-	"fdt_high=0xffffffff\0" \
 	"dev=mmc\0" \
 	"devnum=2\0" \
 	"rootdev=mmcblk0p\0" \
 	"quiet=quiet loglevel=0\0" \
-	"console=" CONSOLE_DEV "\0" \
 	"setargs=setenv bootargs root=/dev/${rootdev}${partnum} " \
 		"ro rootwait cma=128M " \
 		"bootcause=${bootcause} " \
-		"${quiet} console=${console} ${rtc_status} " \
+		"${quiet} " \
 		"${videoargs}" "\0" \
 	"doquiet=" \
 		"if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
 			"then setenv quiet; fi\0" \
 	"hasfirstboot=" \
-		"ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \
-		"/boot/bootcause/firstboot\0" \
+		"test -e ${dev} ${devnum}:${partnum} /boot/bootcause/firstboot\0" \
 	"swappartitions=" \
 		"setexpr partnum 3 - ${partnum}\0" \
 	"failbootcmd=" \
-		"bx50_backlight_enable; " \
-		"msg=\"Monitor failed to start.  Try again, or contact GE Service for support.\"; " \
-		"echo $msg; " \
-		"setenv stdout vga; " \
-		"echo \"\n\n\n\n    \" $msg; " \
-		"setenv stdout serial; " \
-		"mw.b 0x7000A000 0xbc; " \
-		"mw.b 0x7000A001 0x00; " \
-		"ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
+		"cls; " \
+		"setcurs 5 4; " \
+		"lcdputs \"Monitor failed to start. " \
+		"Try again, or contact GE Service for support.\"; " \
+		"bootcount reset; " \
+		"while true; do sleep 1; done; \0" \
 	"altbootcmd=" \
 		"run doquiet; " \
 		"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
 		"run hasfirstboot || setenv partnum 0; " \
 		"if test ${partnum} != 0; then " \
-			"setenv bootcause REVERT; " \
 			"run swappartitions loadimage doboot; " \
 		"fi; " \
 		"run failbootcmd\0" \
@@ -137,43 +90,29 @@
 	"doboot=" \
 		"echo Booting from ${dev}:${devnum}:${partnum} ...; " \
 		"run setargs; " \
-		"bootm ${loadaddr}#conf@${confidx}\0" \
+		"bootm ${loadaddr}\0" \
 	"tryboot=" \
 		"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
 		"run loadimage || run swappartitions && run loadimage || " \
-		"setenv partnum 0 && echo MISSING IMAGE;" \
+			"setenv partnum 0 && echo MISSING IMAGE;" \
 		"run doboot; " \
 		"run failbootcmd\0" \
 
-#define CONFIG_MMCBOOTCOMMAND \
-	"if mmc dev ${devnum}; then " \
-		"run doquiet; " \
-		"run tryboot; " \
-	"fi; " \
-
-#define CONFIG_USBBOOTCOMMAND \
-	"echo Unsupported; " \
+#define MMCBOOTCOMMAND \
+	"run doquiet; " \
+	"run tryboot; " \
 
-#ifdef CONFIG_NFS_CMD
-#define CONFIG_BOOTCOMMAND CONFIG_NETWORKBOOTCOMMAND
-#elif CONFIG_CMD_USB
-#define CONFIG_BOOTCOMMAND CONFIG_USBBOOTCOMMAND
+#ifdef CONFIG_CMD_NFS
+#define CONFIG_BOOTCOMMAND NETWORKBOOTCOMMAND
 #else
-#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
+#define CONFIG_BOOTCOMMAND MMCBOOTCOMMAND
 #endif
 
-
-/* Miscellaneous configurable options */
-
-#define CONFIG_SYS_MEMTEST_START       0x10000000
-#define CONFIG_SYS_MEMTEST_END         0x10010000
-#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
-
-#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
-
 /* Physical Memory Map */
 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20)     /* 256M */
+
 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
@@ -191,44 +130,11 @@
 #define CONFIG_HIDE_LOGO_VERSION
 #define CONFIG_IMX_HDMI
 #define CONFIG_IMX_VIDEO_SKIP
-#define CONFIG_CMD_BMP
 
 #define CONFIG_IMX6_PWM_PER_CLK	66000000
 
-#define CONFIG_PCI
-#define CONFIG_PCI_PNP
 #define CONFIG_PCI_SCAN_SHOW
 #define CONFIG_PCIE_IMX
-#define CONFIG_PCIE_IMX_PERST_GPIO	IMX_GPIO_NR(7, 12)
 #define CONFIG_PCIE_IMX_POWER_GPIO	IMX_GPIO_NR(1, 5)
 
-#define CONFIG_RTC_RX8010SJ
-#define CONFIG_SYS_RTC_BUS_NUM 2
-#define CONFIG_SYS_I2C_RTC_ADDR	0x32
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_SPEED		  100000
-#define CONFIG_SYS_I2C_MXC_I2C1
-#define CONFIG_SYS_I2C_MXC_I2C2
-#define CONFIG_SYS_I2C_MXC_I2C3
-
-#define CONFIG_SYS_NUM_I2C_BUSES        11
-#define CONFIG_SYS_I2C_MAX_HOPS         1
-#define CONFIG_SYS_I2C_BUSES	{	{0, {I2C_NULL_HOP} }, \
-					{1, {I2C_NULL_HOP} }, \
-					{2, {I2C_NULL_HOP} }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
-				}
-
-#define CONFIG_BCH
-
 #endif	/* __GE_BX50V3_CONFIG_H */