X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fds414.h;h=1205e8597d9a94c1e95cf56987536c8549f9ecae;hb=55dabcc8f24598e2777f663de09ab55fbe1269da;hp=27308c92ffb99a55cde2ed7629d2db68453abcd3;hpb=582d97b6d37ed1bfce575c32d3847a42fc633b8e;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/ds414.h b/include/configs/ds414.h
index 27308c9..1205e85 100644
--- a/include/configs/ds414.h
+++ b/include/configs/ds414.h
@@ -6,6 +6,9 @@
 #ifndef _CONFIG_SYNOLOGY_DS414_H
 #define _CONFIG_SYNOLOGY_DS414_H
 
+/* Vendor kernel expects this MACH_TYPE */
+#define CONFIG_MACH_TYPE	3036
+
 /*
  * High Level Configuration Options (easy to change)
  */
@@ -15,54 +18,19 @@
  * for DDR ECC byte filling in the SPL before loading the main
  * U-Boot into it.
  */
-#define CONFIG_SYS_TCLK		250000000	/* 250MHz */
-
-/*
- * Commands configuration
- */
 
 /* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MVTWSI
 #define CONFIG_I2C_MVTWSI_BASE0		MVEBU_TWSI_BASE
 #define CONFIG_SYS_I2C_SLAVE		0x0
 #define CONFIG_SYS_I2C_SPEED		100000
 
-/* SPI NOR flash default params, used by sf commands */
-#define CONFIG_SF_DEFAULT_SPEED		1000000
-#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_3
-
-/* Environment in SPI NOR flash */
-#define CONFIG_ENV_OFFSET		0x7E0000   /* RedBoot config partition in DTS */
-#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
-#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */
-
-#define CONFIG_SYS_NETA_INTERFACE_TYPE	PHY_INTERFACE_MODE_RGMII
-
 /* PCIe support */
 #ifndef CONFIG_SPL_BUILD
-#define CONFIG_PCI_MVEBU
 #define CONFIG_PCI_SCAN_SHOW
 #endif
 
 /* USB/EHCI/XHCI configuration */
-
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-
-/* FIXME: broken XHCI support
- * Below defines should enable support for the two rear USB3 ports. Sadly, this
- * does not work because:
- * - xhci-pci seems to not support DM_USB, so with that enabled it is not
- *   found.
- * - USB init fails, controller does not respond in time */
-
-#if !defined(CONFIG_USB_XHCI_HCD)
 #define CONFIG_EHCI_IS_TDI
-#endif
-
-/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_MTD_PARTITIONS
 
 /*
  * mv-common.h should be defined after CMD configs since it used them
@@ -85,7 +53,6 @@
 
 /* SPL */
 /* Defines for SPL */
-#define CONFIG_SPL_TEXT_BASE		0x40004030
 #define CONFIG_SPL_MAX_SIZE		((128 << 10) - 0x4030)
 
 #define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + (128 << 10))
@@ -98,16 +65,29 @@
 #define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-/* SPL related SPI defines */
-#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x24000
-
 /* DS414 bus width is 32bits */
 #define CONFIG_DDR_32BIT
 
 /* Default Environment */
-#define CONFIG_BOOTCOMMAND	"sf read ${loadaddr} 0xd0000 0x700000; bootm"
 #define CONFIG_LOADADDR		0x80000
-#undef CONFIG_PREBOOT		/* override preboot for USB and SPI flash init */
-#define CONFIG_PREBOOT		"usb start; sf probe"
+#define CONFIG_BOOTCOMMAND					\
+	"sf probe; "						\
+	"sf read ${loadaddr} 0xd0000 0x2d0000; "		\
+	"sf read ${ramdisk_addr_r} 0x3a0000 0x430000; "		\
+	"bootm ${loadaddr} ${ramdisk_addr_r}"
+
+#define CONFIG_EXTRA_ENV_SETTINGS				\
+	"initrd_high=0xffffffff\0"				\
+	"ramdisk_addr_r=0x8000000\0"				\
+	"usb0Mode=host\0usb1Mode=host\0usb2Mode=device\0"	\
+	"ethmtu=1500\0eth1mtu=1500\0"				\
+	"update_uboot=sf probe; dhcp; "				\
+		"mw.b ${loadaddr} 0x0 0xd0000; "		\
+		"tftpboot ${loadaddr} u-boot-spl.kwb; "		\
+		"sf update ${loadaddr} 0x0 0xd0000\0"
+
+
+/* increase autoneg timeout, my NIC sucks */
+#define PHY_ANEG_TIMEOUT	16000
 
 #endif /* _CONFIG_SYNOLOGY_DS414_H */