X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fdevkit3250.h;h=4ad4570caa0d5420be3cb028c39769325f6e642d;hb=1f20fc53b382ece8da7440f354b219deb7ed19df;hp=2e8522a9218edfa41890e10bc4286654a136f072;hpb=77d2f7f5070c7def29d433096f4cee57eeddbd23;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/devkit3250.h b/include/configs/devkit3250.h
index 2e8522a..4ad4570 100644
--- a/include/configs/devkit3250.h
+++ b/include/configs/devkit3250.h
@@ -13,10 +13,6 @@
 #include <linux/sizes.h>
 #include <asm/arch/cpu.h>
 
-/*
- * Define DevKit3250 machine type by hand until it lands in mach-types
- */
-#define MACH_TYPE_DEVKIT3250		3697
 #define CONFIG_MACH_TYPE		MACH_TYPE_DEVKIT3250
 
 #define CONFIG_SYS_ICACHE_OFF
@@ -24,7 +20,6 @@
 #if !defined(CONFIG_SPL_BUILD)
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #endif
-#define CONFIG_BOARD_EARLY_INIT_F
 
 /*
  * Memory configurations
@@ -46,7 +41,6 @@
  * Serial Driver
  */
 #define CONFIG_SYS_LPC32XX_UART		5   /* UART5 */
-#define CONFIG_BAUDRATE			115200
 
 /*
  * DMA
@@ -79,7 +73,6 @@
 #define CONFIG_RMII
 #define CONFIG_PHY_SMSC
 #define CONFIG_LPC32XX_ETH
-#define CONFIG_PHYLIB
 #define CONFIG_PHY_ADDR			0x1F
 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 
@@ -116,9 +109,6 @@
 #define CONFIG_SYS_NAND_PAGE_SIZE		NAND_LARGE_BLOCK_PAGE_SIZE
 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NAND
-
 /*
  * USB
  */
@@ -130,15 +120,10 @@
  */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_CBSIZE		1024
-#define CONFIG_SYS_PBSIZE		\
-	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_CMDLINE_EDITING
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DOS_PARTITION
 
 /*
  * Pass open firmware flat tree
@@ -147,7 +132,6 @@
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_NAND		1
 #define CONFIG_ENV_SIZE			SZ_128K
 #define CONFIG_ENV_OFFSET		0x000A0000
 
@@ -178,7 +162,6 @@
 #define CONFIG_SETUP_MEMORY_TAGS
 
 #define CONFIG_BOOTFILE			"uImage"
-#define CONFIG_BOOTARGS			"console=ttyS0,115200n8"
 #define CONFIG_LOADADDR			0x80008000
 
 /*
@@ -189,19 +172,15 @@
 
 /* SPL will use SRAM as stack */
 #define CONFIG_SPL_STACK		0x0000FFF8
-#define CONFIG_SPL_BOARD_INIT
 
 /* Use the framework and generic lib */
 #define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
 
 /* SPL will use serial */
-#define CONFIG_SPL_SERIAL_SUPPORT
 
 /* SPL loads an image from NAND */
 #define CONFIG_SPL_NAND_SIMPLE
 #define CONFIG_SPL_NAND_RAW_ONLY
-#define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_NAND_DRIVERS
 
 #define CONFIG_SPL_NAND_ECC