X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fdavinci_dvevm.h;h=e4443ec89e4e1a57dbf077068bbf4813682841e7;hb=219f4788d33b04e394d4ade1feaedc0292acc790;hp=c27ce18ff2b6e516b2892663070765d67befa80b;hpb=00b1883a4cac59d97cd297b1a3a398db85982865;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/davinci_dvevm.h b/include/configs/davinci_dvevm.h index c27ce18..e4443ec 100644 --- a/include/configs/davinci_dvevm.h +++ b/include/configs/davinci_dvevm.h @@ -19,7 +19,6 @@ #ifndef __CONFIG_H #define __CONFIG_H -#include /* * Define this to make U-Boot skip low level initialization when loaded @@ -50,54 +49,53 @@ /* Board */ /*=======*/ #define DV_EVM -#define CFG_NAND_SMALLPAGE -#define CFG_USE_NOR +#define CONFIG_SYS_NAND_SMALLPAGE +#define CONFIG_SYS_USE_NAND /*===================*/ /* SoC Configuration */ /*===================*/ #define CONFIG_ARM926EJS /* arm926ejs CPU core */ -#define CONFIG_SYS_CLK_FREQ 297000000 /* Arm Clock frequency */ -#define CFG_TIMERBASE 0x01c21400 /* use timer 0 */ -#define CFG_HZ_CLOCK 27000000 /* Timer Input clock freq */ -#define CFG_HZ 1000 +#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */ +#define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */ +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SOC_DM644X /*====================================================*/ /* EEPROM definitions for Atmel 24C256BN SEEPROM chip */ /* on Sonata/DV_EVM board. No EEPROM on schmoogie. */ /*====================================================*/ -#define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_I2C_EEPROM_ADDR 0x50 -#define CFG_EEPROM_PAGE_WRITE_BITS 6 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 /*=============*/ /* Memory Info */ /*=============*/ -#define CFG_MALLOC_LEN (0x10000 + 128*1024) /* malloc() len */ -#define CFG_GBL_DATA_SIZE 128 /* reserved for initial data */ -#define CFG_MEMTEST_START 0x80000000 /* memtest start address */ -#define CFG_MEMTEST_END 0x81000000 /* 16MB RAM test */ +#define CONFIG_SYS_MALLOC_LEN (0x10000 + 128*1024) /* malloc() len */ +#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */ +#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */ #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ #define CONFIG_STACKSIZE (256*1024) /* regular stack */ #define PHYS_SDRAM_1 0x80000000 /* DDR Start */ #define PHYS_SDRAM_1_SIZE 0x10000000 /* DDR size 256MB */ + #define DDR_8BANKS /* 8-bank DDR2 (256MB) */ /*====================*/ /* Serial Driver info */ /*====================*/ -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 4 /* NS16550 register size */ -#define CFG_NS16550_COM1 0x01c20000 /* Base address of UART0 */ -#define CFG_NS16550_CLK 27000000 /* Input clock to NS16550 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size, byteorder */ +#define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */ +#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK /* Input clock to NS16550 */ #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ #define CONFIG_BAUDRATE 115200 /* Default baud rate */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /*===================*/ /* I2C Configuration */ /*===================*/ #define CONFIG_HARD_I2C #define CONFIG_DRIVER_DAVINCI_I2C -#define CFG_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */ -#define CFG_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ +#define CONFIG_SYS_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */ +#define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ /*==================================*/ /* Network & Ethernet Configuration */ /*==================================*/ @@ -111,45 +109,50 @@ /*=====================*/ /* Flash & Environment */ /*=====================*/ -#ifdef CFG_USE_NAND -#undef CFG_ENV_IS_IN_FLASH -#define CFG_NO_FLASH -#define CFG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ -#ifdef CFG_NAND_SMALLPAGE -#define CFG_ENV_SECT_SIZE 512 /* Env sector Size */ -#define CFG_ENV_SIZE SZ_16K +#ifdef CONFIG_SYS_USE_NAND +#define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_CS 2 +#undef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ +#ifdef CONFIG_SYS_NAND_SMALLPAGE +#define CONFIG_ENV_SECT_SIZE 512 /* Env sector Size */ +#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */ +#define CONFIG_MTD_PARTITIONS +#define CONFIG_MTD_DEVICE +#define CONFIG_CMD_MTDPARTS +#define MTDIDS_DEFAULT \ + "nand0=davinci_nand.0" +#define MTDPARTS_DEFAULT \ + "mtdparts=davinci_nand.0:384k(bootloader)ro,4m(kernel),-(filesystem)" #else -#define CFG_ENV_SECT_SIZE 2048 /* Env sector Size */ -#define CFG_ENV_SIZE SZ_128K +#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */ +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ #endif #define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ -#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ -#define CFG_NAND_BASE 0x02000000 -#define CFG_NAND_HW_ECC -#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define NAND_MAX_CHIPS 1 -#define CFG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ -#define DEF_BOOTM "" -#elif defined(CFG_USE_NOR) +#define CONFIG_SYS_NAND_BASE 0x02000000 +#define CONFIG_SYS_NAND_USE_FLASH_BBT +#define CONFIG_SYS_NAND_HW_ECC +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ +#elif defined(CONFIG_SYS_USE_NOR) #ifdef CONFIG_NOR_UART_BOOT #define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ -#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ #else #undef CONFIG_SKIP_LOWLEVEL_INIT -#undef CONFIG_SKIP_RELOCATE_UBOOT #endif -#define CFG_ENV_IS_IN_FLASH -#undef CFG_NO_FLASH +#define CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_SYS_NO_FLASH #define CONFIG_FLASH_CFI_DRIVER -#define CFG_FLASH_CFI -#define CFG_MAX_FLASH_BANKS 1 /* max number of flash banks */ -#define CFG_FLASH_SECT_SZ 0x10000 /* 64KB sect size AMD Flash */ -#define CFG_ENV_OFFSET (CFG_FLASH_SECT_SZ*3) +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */ +#define CONFIG_SYS_FLASH_SECT_SZ 0x10000 /* 64KB sect size AMD Flash */ +#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3) #define PHYS_FLASH_1 0x02000000 /* CS2 Base address */ -#define CFG_FLASH_BASE PHYS_FLASH_1 /* Flash Base for U-Boot */ +#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 /* Flash Base for U-Boot */ #define PHYS_FLASH_SIZE 0x2000000 /* Flash size 32MB */ -#define CFG_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CFG_FLASH_SECT_SZ) -#define CFG_ENV_SECT_SIZE CFG_FLASH_SECT_SZ /* Env sector Size */ +#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ) +#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ /* Env sector Size */ #endif /*==============================*/ /* U-Boot general configuration */ @@ -158,20 +161,21 @@ #define CONFIG_MISC_INIT_R #undef CONFIG_BOOTDELAY #define CONFIG_BOOTFILE "uImage" /* Boot file name */ -#define CFG_PROMPT "U-Boot > " /* Monitor Command Prompt */ -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print buffer sz */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_LOAD_ADDR 0x80700000 /* default Linux kernel load address */ +#define CONFIG_SYS_PROMPT "U-Boot > " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buffer sz */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* default Linux kernel load address */ #define CONFIG_VERSION_VARIABLE #define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */ -#define CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER #define CONFIG_CMDLINE_EDITING -#define CFG_LONGHELP +#define CONFIG_SYS_LONGHELP #define CONFIG_CRC32_VERIFY #define CONFIG_MX_CYCLIC +#define CONFIG_MUSB_HCD +#define CONFIG_USB_DAVINCI /*===================*/ /* Linux Information */ /*===================*/ @@ -193,22 +197,45 @@ #define CONFIG_CMD_SAVES #define CONFIG_CMD_EEPROM #undef CONFIG_CMD_BDI + +#ifdef CONFIG_CMD_BDI +#define CONFIG_CLOCKS +#endif + #undef CONFIG_CMD_FPGA #undef CONFIG_CMD_SETGETDCR -#ifdef CFG_USE_NAND +#ifdef CONFIG_SYS_USE_NAND #undef CONFIG_CMD_FLASH #undef CONFIG_CMD_IMLS #define CONFIG_CMD_NAND -#elif defined(CFG_USE_NOR) +#elif defined(CONFIG_SYS_USE_NOR) #define CONFIG_CMD_JFFS2 #else -#error "Either CFG_USE_NAND or CFG_USE_NOR _MUST_ be defined !!!" +#error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!" +#endif +/*==========================*/ +/* USB MSC support (if any) */ +/*==========================*/ +#ifdef CONFIG_USB_DAVINCI +#define CONFIG_CMD_USB +#ifdef CONFIG_MUSB_HCD +#define CONFIG_USB_STORAGE +#define CONFIG_CMD_STORAGE +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION #endif -/*=======================*/ -/* KGDB support (if any) */ -/*=======================*/ -#ifdef CONFIG_CMD_KGDB -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ +#ifdef CONFIG_USB_KEYBOARD +#define CONFIG_SYS_USB_EVENT_POLL +#define CONFIG_PREBOOT "usb start" #endif +#endif + +#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */ + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) + #endif /* __CONFIG_H */