X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fcontrolcenterdc.h;h=cad5796cbce66aea19552056bc9b7b2752fb1696;hb=d2e5250be49fce4653689c41a5dc7e2d7e7ecf33;hp=869b94bc9b5e9327dc3f65a8294402a1f3bc3394;hpb=16acff8cfcff51edc987572bfe937d1ae36be444;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/controlcenterdc.h b/include/configs/controlcenterdc.h
index 869b94b..cad5796 100644
--- a/include/configs/controlcenterdc.h
+++ b/include/configs/controlcenterdc.h
@@ -12,30 +12,12 @@
  */
 #define CONFIG_CUSTOMER_BOARD_SUPPORT
 
-#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-
 /*
  * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
  * for DDR ECC byte filling in the SPL before loading the main
  * U-Boot into it.
  */
 
-#define CONFIG_SYS_TCLK		250000000	/* 250MHz */
-
-#define CONFIG_LOADADDR 		1000000
-
-/*
- * SATA/SCSI/AHCI configuration
- */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID	2
-#define CONFIG_SYS_SCSI_MAX_LUN		1
-#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-					 CONFIG_SYS_SCSI_MAX_LUN)
-
-/* USB/EHCI configuration */
-#define CONFIG_EHCI_IS_TDI
-
 /* Environment in SPI NOR flash */
 
 #define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */
@@ -81,22 +63,8 @@
 #define CONFIG_SPL_STACK		(0x40000000 + ((212 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
 
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-
-#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
-/* SPL related SPI defines */
-#define CONFIG_SYS_U_BOOT_OFFS		CONFIG_SYS_SPI_U_BOOT_OFFS
-#endif
-
 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
 /* SPL related MMC defines */
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
-#define CONFIG_SYS_MMC_U_BOOT_OFFS		(168 << 10)
-#define CONFIG_SYS_U_BOOT_OFFS			CONFIG_SYS_MMC_U_BOOT_OFFS
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	(CONFIG_SYS_U_BOOT_OFFS / 512)
 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
 #endif
@@ -108,7 +76,6 @@
 
 #define CONFIG_HOSTNAME		"ccdc"
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
-#define CONFIG_BOOTFILE		"ccdc.img"
 
 #define CONFIG_EXTRA_ENV_SETTINGS						\
 	"netdev=eth1\0"						\
@@ -145,26 +112,6 @@
 		" gpio clear ${gpio1}; gpio set ${gpio2};"			\
 		" fi; sleep 0.12; done\0"
 
-#define CONFIG_NFSBOOTCOMMAND								\
-	"setenv bootargs root=/dev/nfs rw "						\
-	"nfsroot=${serverip}:${rootpath} "						\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off "	\
-	"console=${consoledev},${baudrate} ${othbootargs}; "				\
-	"tftpboot ${bootfile_addr} ${bootfile}; "						\
-	"bootm ${bootfile_addr}"
-
-#define CONFIG_MMCBOOTCOMMAND					\
-	"setenv bootargs root=/dev/mmcblk0p3 rw rootwait "	\
-	"console=${consoledev},${baudrate} ${othbootargs}; "	\
-	"ext2load mmc 0:2 ${bootfile_addr} ${bootfile}; "	\
-	"bootm ${bootfile_addr}"
-
-#define CONFIG_BOOTCOMMAND			\
-	"if env exists keyprogram; then;"	\
-	" setenv keyprogram; run nfsboot;"	\
-        " fi;"					\
-        " run dobootfail"
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros