X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fcontrolcenterdc.h;h=119a834fe742995cd157d64688eaf3224ead2364;hb=54f80dd2908af0b851816cf062edf2d454948397;hp=171bd189d3bad621eb5515be88d49b45f6a1d352;hpb=aba3fa1d3f1dc8f7049317b8d6ea1d8cb8935e5e;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/controlcenterdc.h b/include/configs/controlcenterdc.h
index 171bd18..119a834 100644
--- a/include/configs/controlcenterdc.h
+++ b/include/configs/controlcenterdc.h
@@ -8,99 +8,19 @@
 #define _CONFIG_CONTROLCENTERDC_H
 
 /*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_CUSTOMER_BOARD_SUPPORT
-
-#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-
-/*
  * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
  * for DDR ECC byte filling in the SPL before loading the main
  * U-Boot into it.
  */
 
-#define CONFIG_SYS_TCLK		250000000	/* 250MHz */
-
-#define CONFIG_LOADADDR 		1000000
-
-/*
- * SATA/SCSI/AHCI configuration
- */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID	2
-#define CONFIG_SYS_SCSI_MAX_LUN		1
-#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-					 CONFIG_SYS_SCSI_MAX_LUN)
-
-/* USB/EHCI configuration */
-#define CONFIG_EHCI_IS_TDI
-
 /* Environment in SPI NOR flash */
 
 #define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */
 
-/* PCIe support */
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_PCI_SCAN_SHOW
-#endif
-
-/*
- * Software (bit-bang) MII driver configuration
- */
-#define CONFIG_BITBANGMII_MULTI
-
-/* SPL */
-/*
- * Select the boot device here
- *
- * Currently supported are:
- * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
- * SPL_BOOT_SDIO_MMC_CARD	- Booting via SDIO/MMC card (partition 1)
- */
-#define SPL_BOOT_SPI_NOR_FLASH		1
-#define SPL_BOOT_SDIO_MMC_CARD		2
-#define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SPI_NOR_FLASH
-
-/* Defines for SPL */
-#define CONFIG_SPL_SIZE			(160 << 10)
-
-#if defined(CONFIG_SECURED_MODE_IMAGE)
-#define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - 0x2614)
-#else
-#define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - 0x30)
-#endif
-
-#define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + CONFIG_SPL_SIZE)
-#define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)
-
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MALLOC_SIMPLE
-#endif
-
-#define CONFIG_SPL_STACK		(0x40000000 + ((212 - 16) << 10))
-#define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)
-
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_I2C
-
-#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
-/* SPL related MMC defines */
-#define CONFIG_SPL_MMC_SUPPORT
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
-#endif
-#endif
-
 /*
  * Environment Configuration
  */
 
-#define CONFIG_HOSTNAME		"ccdc"
-#define CONFIG_ROOTPATH		"/opt/nfsroot"
-#define CONFIG_BOOTFILE		"ccdc.img"
-
 #define CONFIG_EXTRA_ENV_SETTINGS						\
 	"netdev=eth1\0"						\
 	"consoledev=ttyS1\0"							\
@@ -136,26 +56,6 @@
 		" gpio clear ${gpio1}; gpio set ${gpio2};"			\
 		" fi; sleep 0.12; done\0"
 
-#define CONFIG_NFSBOOTCOMMAND								\
-	"setenv bootargs root=/dev/nfs rw "						\
-	"nfsroot=${serverip}:${rootpath} "						\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off "	\
-	"console=${consoledev},${baudrate} ${othbootargs}; "				\
-	"tftpboot ${bootfile_addr} ${bootfile}; "						\
-	"bootm ${bootfile_addr}"
-
-#define CONFIG_MMCBOOTCOMMAND					\
-	"setenv bootargs root=/dev/mmcblk0p3 rw rootwait "	\
-	"console=${consoledev},${baudrate} ${othbootargs}; "	\
-	"ext2load mmc 0:2 ${bootfile_addr} ${bootfile}; "	\
-	"bootm ${bootfile_addr}"
-
-#define CONFIG_BOOTCOMMAND			\
-	"if env exists keyprogram; then;"	\
-	" setenv keyprogram; run nfsboot;"	\
-        " fi;"					\
-        " run dobootfail"
-
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros