X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fcontrolcenterd.h;h=08def6251acb3e93b320a85ae21afeaf33b45c7e;hb=1989374b21089c63019fc9648408c8d609023ffe;hp=b824e3bd2348e87c23cdf825fb49952c9f92594f;hpb=feb9e25bc706c85c0eb4d6c467379b5236f8de5f;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/controlcenterd.h b/include/configs/controlcenterd.h
index b824e3b..08def62 100644
--- a/include/configs/controlcenterd.h
+++ b/include/configs/controlcenterd.h
@@ -35,14 +35,10 @@
 #endif
 
 /* High Level Configuration Options */
-#define CONFIG_BOOKE			/* BOOKE */
-#define CONFIG_E500			/* BOOKE e500 family */
 #define CONFIG_CONTROLCENTERD
 #define CONFIG_MP			/* support multiple processors */
 
-#define CONFIG_SYS_NO_FLASH
 #define CONFIG_ENABLE_36BIT_PHYS
-#define CONFIG_FSL_LAW			/* Use common FSL init code */
 
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_ADDR_MAP
@@ -125,8 +121,6 @@
 #define CONFIG_SYS_SDRAM_SIZE 1024
 #define CONFIG_VERY_BIG_RAM
 
-#define CONFIG_SYS_FSL_DDR3
-#define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
@@ -142,7 +136,6 @@
 /*
  * Local Bus Definitions
  */
-#define CONFIG_FSL_ELBC			/* Has Enhanced localbus controller */
 
 #define CONFIG_SYS_ELBC_BASE		0xe0000000
 #ifdef CONFIG_PHYS_64BIT
@@ -192,7 +185,6 @@
 
 #define CONFIG_PCA9698			/* NXP PCA9698 */
 
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
 
@@ -206,14 +198,9 @@
 #define CONFIG_SF_DEFAULT_MODE		0
 #endif
 
-#define CONFIG_SHA1
-
 /*
  * MMC
  */
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
 
@@ -224,7 +211,6 @@
  */
 #define CONFIG_FSL_DIU_FB
 #define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x10000)
-#define CONFIG_CMD_BMP
 
 /*
  * General PCI
@@ -262,7 +248,6 @@
  */
 #define CONFIG_LIBATA
 #define CONFIG_LBA48
-#define CONFIG_CMD_SATA
 
 #define CONFIG_FSL_SATA
 #define CONFIG_SYS_SATA_MAX_DEVICE	2
@@ -297,12 +282,9 @@
 
 #define CONFIG_ETHPRIME		"eTSEC1"
 
-#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
-
 /*
  * USB
  */
-#define CONFIG_USB_EHCI
 
 #define CONFIG_HAS_FSL_DR_USB
 #define CONFIG_USB_EHCI_FSL
@@ -314,10 +296,8 @@
  * Environment
  */
 #if defined(CONFIG_TRAILBLAZER)
-#define CONFIG_ENV_IS_NOWHERE
 #define CONFIG_ENV_SIZE		0x2000		/* 8KB */
 #elif defined(CONFIG_RAMBOOT_SPIFLASH)
-#define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SPI_BUS	0
 #define CONFIG_ENV_SPI_CS	0
 #define CONFIG_ENV_SPI_MAX_HZ	10000000
@@ -326,7 +306,6 @@
 #define CONFIG_ENV_OFFSET	0x100000	/* 1MB */
 #define CONFIG_ENV_SECT_SIZE	0x10000
 #elif defined(CONFIG_RAMBOOT_SDCARD)
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_FSL_FIXED_MMC_LOCATION
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_SYS_MMC_ENV_DEV	0
@@ -356,21 +335,17 @@
 
 #ifndef CONFIG_TRAILBLAZER
 
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
 
 /*
  * Board initialisation callbacks
  */
-#define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_EARLY_INIT_R
 #define CONFIG_MISC_INIT_R
 #define CONFIG_LAST_STAGE_INIT
 
 #else /* CONFIG_TRAILBLAZER */
 
-#define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_EARLY_INIT_R
 #define CONFIG_LAST_STAGE_INIT
 
@@ -382,7 +357,6 @@
 #define CONFIG_HW_WATCHDOG
 #define CONFIG_LOADS_ECHO
 #define CONFIG_SYS_LOADS_BAUD_CHANGE
-#define CONFIG_DOS_PARTITION
 
 /*
  * For booting Linux, the board info and command line data
@@ -397,9 +371,6 @@
  */
 
 #ifdef CONFIG_TRAILBLAZER
-
-#define CONFIG_BAUDRATE	115200
-
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"mp_holdoff=1\0"
 
@@ -412,9 +383,6 @@
 
 #define CONFIG_LOADADDR		1000000
 
-
-#define CONFIG_BAUDRATE	115200
-
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"netdev=eth0\0"						\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\