X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fcobra5272.h;h=6d6e2fc696200f85f91e860441404f17e25ca13d;hb=9b0240f8c6a1caa42da73835090fcb6db60f3d23;hp=337c875655ccaef5564781b44e1d4e04fcf71967;hpb=b71d9e8b3805305ea4116733f515061710ad7081;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h index 337c875..6d6e2fc 100644 --- a/include/configs/cobra5272.h +++ b/include/configs/cobra5272.h @@ -29,41 +29,18 @@ * --- */ -#define CONFIG_SYS_CLK 66000000 -#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ - -/* --- - * Enable use of Ethernet - * --- - */ -#define CONFIG_MCFFEC - -/* Enable Dma Timer */ -#define CONFIG_MCFTMR +#define CFG_SYS_CLK 66000000 +#define CFG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ /* --- * Define baudrate for UART1 (console output, tftp, ...) * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud - * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command + * CFG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command * interface * --- */ -#define CONFIG_MCFUART -#define CONFIG_SYS_UART_PORT (0) - -/* --- - * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change - * timeout acc. to your needs - * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000 - * for 10 sec - * --- - */ - -#if 0 -#define CONFIG_WATCHDOG -#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ -#endif +#define CFG_SYS_UART_PORT (0) /* --- * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different @@ -76,7 +53,7 @@ * * Setting #if 0: u-boot will start from flash and relocate itself to RAM * - * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE + * Please do not forget to modify the setting of CONFIG_TEXT_BASE * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000) * * --- @@ -92,48 +69,11 @@ * --- */ -#ifndef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_ENV_OFFSET 0x4000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#else -#define CONFIG_ENV_ADDR 0xffe04000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#endif - #define LDS_BOARD_TEXT \ . = DEFINED(env_offset) ? env_offset : .; \ env/embedded.o(.text); /* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -#ifdef CONFIG_MCFFEC -# define CONFIG_MII_INIT 1 -# define CONFIG_SYS_DISCOVER_PHY -# define CONFIG_SYS_RX_ETH_BUFFER 8 -# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN - -# define CONFIG_SYS_FEC0_PINMUX 0 -# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE -# define MCFFEC_TOUT_LOOP 50000 -/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ -# ifndef CONFIG_SYS_DISCOVER_PHY -# define FECDUPLEX FULL -# define FECSPEED _100BASET -# else -# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN -# endif -# endif /* CONFIG_SYS_DISCOVER_PHY */ -#endif - -/* *----------------------------------------------------------------------------- * Define user parameters that have to be customized most likely *----------------------------------------------------------------------------- @@ -147,7 +87,6 @@ u-boot: 'set' command */ #if 0 -#define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please enter a valid image address in flash */ /* User network settings */ @@ -157,9 +96,6 @@ enter a valid image address in flash */ #endif -#define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address -from which user programs will be started */ - /*---*/ /* @@ -173,9 +109,6 @@ from which user programs will be started */ * --- */ -#define CONFIG_SYS_MEMTEST_START 0x400 -#define CONFIG_SYS_MEMTEST_END 0x380000 - /* --- * Low Level Configuration Settings * (address mappings, register initial values, etc.) @@ -188,38 +121,28 @@ from which user programs will be started */ * --- */ -#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ +#define CFG_SYS_MBAR 0x10000000 /* Register Base Addrs */ /* --- * System Conf. Reg. & System Protection Reg. * --- */ -#define CONFIG_SYS_SCR 0x0003 -#define CONFIG_SYS_SPR 0xffff - -/* --- - * Ethernet settings - * --- - */ - -#define CONFIG_SYS_DISCOVER_PHY -#define CONFIG_SYS_ENET_BD_BASE 0x780000 +#define CFG_SYS_SCR 0x0003 +#define CFG_SYS_SPR 0xffff /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in internal SRAM) */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CFG_SYS_INIT_RAM_ADDR 0x20000000 +#define CFG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + * Please note that CFG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CFG_SYS_SDRAM_BASE 0x00000000 /* *------------------------------------------------------------------------- @@ -227,87 +150,39 @@ from which user programs will be started */ *----------------------------------------------------------------------- */ -/* #define CONFIG_SYS_SDRAM_SIZE 16 */ +/* #define CFG_SYS_SDRAM_SIZE 16 */ /* *----------------------------------------------------------------------- */ -#define CONFIG_SYS_FLASH_BASE 0xffe00000 - -#ifdef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_SYS_MONITOR_BASE 0x20000 -#else -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) -#endif - -#define CONFIG_SYS_MONITOR_LEN 0x20000 -#define CONFIG_SYS_MALLOC_LEN (256 << 10) -#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 +#define CFG_SYS_FLASH_BASE 0xffe00000 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */ +#define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 16 - -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) -#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + +#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \ + CFG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \ + CFG_SYS_INIT_RAM_SIZE - 4) +#define CFG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \ CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ +#define CFG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ CF_CACR_DISD | CF_CACR_INVI | \ CF_CACR_CEIB | CF_CACR_DCM | \ CF_CACR_EUSP) /*----------------------------------------------------------------------- - * Memory bank definitions - * - * Please refer also to Motorola Coldfire user manual - Chapter XXX - * - */ -#define CONFIG_SYS_BR0_PRELIM 0xFFE00201 -#define CONFIG_SYS_OR0_PRELIM 0xFFE00014 - -#define CONFIG_SYS_BR1_PRELIM 0 -#define CONFIG_SYS_OR1_PRELIM 0 - -#define CONFIG_SYS_BR2_PRELIM 0 -#define CONFIG_SYS_OR2_PRELIM 0 - -#define CONFIG_SYS_BR3_PRELIM 0 -#define CONFIG_SYS_OR3_PRELIM 0 - -#define CONFIG_SYS_BR4_PRELIM 0 -#define CONFIG_SYS_OR4_PRELIM 0 - -#define CONFIG_SYS_BR5_PRELIM 0 -#define CONFIG_SYS_OR5_PRELIM 0 - -#define CONFIG_SYS_BR6_PRELIM 0 -#define CONFIG_SYS_OR6_PRELIM 0 - -#define CONFIG_SYS_BR7_PRELIM 0x00000701 -#define CONFIG_SYS_OR7_PRELIM 0xFF00007C - -/*----------------------------------------------------------------------- * LED config */ #define LED_STAT_0 0xffff /*all LEDs off*/ @@ -322,15 +197,15 @@ from which user programs will be started */ /*----------------------------------------------------------------------- * Port configuration (GPIO) */ -#define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external +#define CFG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external GPIO*/ -#define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs +#define CFG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs (1^=output, 0^=input) */ -#define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ -#define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART +#define CFG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ +#define CFG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART configuration */ -#define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ -#define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */ -#define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */ +#define CFG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ +#define CFG_SYS_PBDAT 0x0000 /* PortB value reg. */ +#define CFG_SYS_PDCNT 0x00000000 /* PortD control reg. */ #endif /* _CONFIG_COBRA5272_H */