X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fcobra5272.h;h=6d6e2fc696200f85f91e860441404f17e25ca13d;hb=9b0240f8c6a1caa42da73835090fcb6db60f3d23;hp=1822ce5120ac76eef7cde841e5e79477b7f1d4ce;hpb=01f1ab67f38882dc7665a0a6eca4bbeba6d84f81;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h index 1822ce5..6d6e2fc 100644 --- a/include/configs/cobra5272.h +++ b/include/configs/cobra5272.h @@ -29,30 +29,18 @@ * --- */ -#define CONFIG_SYS_CLK 66000000 -#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CFG_SYS_CLK 66000000 +#define CFG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ /* --- * Define baudrate for UART1 (console output, tftp, ...) * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud - * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command + * CFG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command * interface * --- */ -#define CONFIG_SYS_UART_PORT (0) - -/* --- - * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change - * timeout acc. to your needs - * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000 - * for 10 sec - * --- - */ - -#if 0 -#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ -#endif +#define CFG_SYS_UART_PORT (0) /* --- * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different @@ -65,7 +53,7 @@ * * Setting #if 0: u-boot will start from flash and relocate itself to RAM * - * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE + * Please do not forget to modify the setting of CONFIG_TEXT_BASE * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000) * * --- @@ -85,15 +73,6 @@ . = DEFINED(env_offset) ? env_offset : .; \ env/embedded.o(.text); -#ifdef CONFIG_MCFFEC -# define CONFIG_SYS_DISCOVER_PHY -/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ -# ifndef CONFIG_SYS_DISCOVER_PHY -# define FECDUPLEX FULL -# define FECSPEED _100BASET -# endif /* CONFIG_SYS_DISCOVER_PHY */ -#endif - /* *----------------------------------------------------------------------------- * Define user parameters that have to be customized most likely @@ -142,38 +121,28 @@ enter a valid image address in flash */ * --- */ -#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ +#define CFG_SYS_MBAR 0x10000000 /* Register Base Addrs */ /* --- * System Conf. Reg. & System Protection Reg. * --- */ -#define CONFIG_SYS_SCR 0x0003 -#define CONFIG_SYS_SPR 0xffff - -/* --- - * Ethernet settings - * --- - */ - -#define CONFIG_SYS_DISCOVER_PHY -#define CONFIG_SYS_ENET_BD_BASE 0x780000 +#define CFG_SYS_SCR 0x0003 +#define CFG_SYS_SPR 0xffff /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in internal SRAM) */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CFG_SYS_INIT_RAM_ADDR 0x20000000 +#define CFG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + * Please note that CFG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CFG_SYS_SDRAM_BASE 0x00000000 /* *------------------------------------------------------------------------- @@ -181,43 +150,34 @@ enter a valid image address in flash */ *----------------------------------------------------------------------- */ -/* #define CONFIG_SYS_SDRAM_SIZE 16 */ +/* #define CFG_SYS_SDRAM_SIZE 16 */ /* *----------------------------------------------------------------------- */ -#define CONFIG_SYS_FLASH_BASE 0xffe00000 - -#define CONFIG_SYS_MONITOR_LEN 0x20000 -#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 +#define CFG_SYS_FLASH_BASE 0xffe00000 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */ +#define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * Cache Configuration */ -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) -#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ +#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \ + CFG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \ + CFG_SYS_INIT_RAM_SIZE - 4) +#define CFG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \ CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ +#define CFG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ CF_CACR_DISD | CF_CACR_INVI | \ CF_CACR_CEIB | CF_CACR_DCM | \ CF_CACR_EUSP) @@ -237,15 +197,15 @@ enter a valid image address in flash */ /*----------------------------------------------------------------------- * Port configuration (GPIO) */ -#define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external +#define CFG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external GPIO*/ -#define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs +#define CFG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs (1^=output, 0^=input) */ -#define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ -#define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART +#define CFG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ +#define CFG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART configuration */ -#define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ -#define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */ -#define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */ +#define CFG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ +#define CFG_SYS_PBDAT 0x0000 /* PortB value reg. */ +#define CFG_SYS_PDCNT 0x00000000 /* PortD control reg. */ #endif /* _CONFIG_COBRA5272_H */