X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fcobra5272.h;h=337c875655ccaef5564781b44e1d4e04fcf71967;hb=bdf97b5d393fc94666a847e9bac1c358b2c63c59;hp=885dfd476166b9a2ad1b81ec69023e1293229ca4;hpb=326ea986ac150acdc7656d57fca647db80b50158;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h
index 885dfd4..337c875 100644
--- a/include/configs/cobra5272.h
+++ b/include/configs/cobra5272.h
@@ -1,13 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Configuation settings for the Sentec Cobra Board.
  *
  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+ 
  */
 
 /* ---
- * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board
+ * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board
  * Date: 2004-03-29
  * Author: Florian Schlote
  *
@@ -25,23 +24,11 @@
 #define _CONFIG_COBRA5272_H
 
 /* ---
- * Define processor
- * possible values for Sentec board: only Coldfire M5272 processor supported
- * (please do not change)
- * ---
- */
-
-#define CONFIG_MCF52x2			/* define processor family */
-#define CONFIG_M5272			/* define processor type */
-
-/* ---
  * Defines processor clock - important for correct timings concerning serial
  * interface etc.
- * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms
  * ---
  */
 
-#define CONFIG_SYS_HZ			1000
 #define CONFIG_SYS_CLK			66000000
 #define CONFIG_SYS_SDRAM_SIZE		16		/* SDRAM size in MB */
 
@@ -64,7 +51,6 @@
 
 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(0)
-#define CONFIG_BAUDRATE		19200
 
 /* ---
  * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
@@ -109,36 +95,25 @@
 #ifndef CONFIG_MONITOR_IS_IN_RAM
 #define CONFIG_ENV_OFFSET		0x4000
 #define CONFIG_ENV_SECT_SIZE	0x2000
-#define CONFIG_ENV_IS_IN_FLASH	1
 #else
 #define CONFIG_ENV_ADDR		0xffe04000
 #define CONFIG_ENV_SECT_SIZE	0x2000
-#define CONFIG_ENV_IS_IN_FLASH	1
 #endif
 
+#define LDS_BOARD_TEXT \
+	. = DEFINED(env_offset) ? env_offset : .; \
+	env/embedded.o(.text);
 
 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
 
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_MII
 
 #ifdef CONFIG_MCFFEC
-#	define CONFIG_MII		1
 #	define CONFIG_MII_INIT		1
 #	define CONFIG_SYS_DISCOVER_PHY
 #	define CONFIG_SYS_RX_ETH_BUFFER	8
@@ -166,12 +141,6 @@
 
 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/
 
-#define CONFIG_BOOTDELAY	5		/* used for autoboot, delay in
-seconds u-boot will wait before starting defined (auto-)boot command, setting
-to -1 disables delay, setting to 0 will too prevent access to u-boot command
-interface: u-boot then has to reflashed */
-
-
 /* The following settings will be contained in the environment block ; if you
 want to use a neutral environment all those settings can be manually set in
 u-boot: 'set' command */
@@ -181,35 +150,18 @@ u-boot: 'set' command */
 #define CONFIG_BOOTCOMMAND	"bootm 0xffe80000"	/*Autoboto command, please
 enter a valid image address in flash */
 
-#define CONFIG_BOOTARGS		" "			/* default bootargs that are
-considered during boot */
-
 /* User network settings */
 
-#define CONFIG_ETHADDR 00:00:00:00:00:09	/* default ethernet MAC addr. */
 #define CONFIG_IPADDR 192.168.100.2		/* default board IP address */
 #define CONFIG_SERVERIP 192.168.100.1	/* default tftp server IP address */
 
 #endif
 
-#define CONFIG_SYS_PROMPT		"COBRA > "	/* Layout of u-boot prompt*/
-
 #define CONFIG_SYS_LOAD_ADDR		0x20000		/*Defines default RAM address
 from which user programs will be started */
 
 /*---*/
 
-#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
 /*
  *-----------------------------------------------------------------------------
  * End of user parameters to be customized