X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fcm_t54.h;h=3787cdc9d4d49038bbaa11194cc5b63cbf432962;hb=83d290c56fab2d38cd1ab4c4cc7099559c1d5046;hp=c8c67c4bab5a91554963fd0d48783e50f0620ecc;hpb=312a6c016a2d81aa3fbc605f5c0c315b6a4e3464;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/cm_t54.h b/include/configs/cm_t54.h
index c8c67c4..3787cdc 100644
--- a/include/configs/cm_t54.h
+++ b/include/configs/cm_t54.h
@@ -1,11 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Config file for Compulab CM-T54 board
  *
  * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
  *
  * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef __CONFIG_CM_T54_H
@@ -16,10 +15,7 @@
 
 #include <configs/ti_omap5_common.h>
 
-#undef CONFIG_SPL_OS_BOOT
-
 /* EEPROM related defines */
-#define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 #define CONFIG_SYS_I2C_EEPROM_BUS	0
@@ -28,22 +24,12 @@
 #define OMAP_HSMMC_USE_GPIO
 
 /* UART setup */
-#define CONFIG_CONS_INDEX		4
 #define CONFIG_SYS_NS16550_COM4		UART4_BASE
-#define CONFIG_BAUDRATE			115200
-
-/* SD/MMC RAW boot */
-#undef CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
-#undef CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS
-
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x200 /* 0x40000 - 256 KB */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x300 /* 384 KB */
 
 /* MMC ENV related defines */
 #undef CONFIG_ENV_OFFSET
 #undef CONFIG_ENV_SIZE
 
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV		1		/* SLOT2: eMMC(1) */
 #define CONFIG_SYS_MMC_ENV_PART		0
 #define CONFIG_ENV_OFFSET		0xc0000		/* (in bytes) 768 KB */
@@ -56,43 +42,30 @@
 #define CONFIG_SUPPORT_EMMC_BOOT
 
 /* SATA Boot related defines */
-#define CONFIG_SPL_SATA_SUPPORT
 #define CONFIG_SPL_SATA_BOOT_DEVICE		0
 #define CONFIG_SYS_SATA_FAT_BOOT_PARTITION	1
 
-#define CONFIG_CMD_SCSI
-#define CONFIG_LIBATA
-#define CONFIG_SCSI_AHCI
 #define CONFIG_SCSI_AHCI_PLAT
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID	1
 #define CONFIG_SYS_SCSI_MAX_LUN		1
 #define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 						CONFIG_SYS_SCSI_MAX_LUN)
 /* USB UHH support options */
-#define CONFIG_CMD_USB
-#define CONFIG_USB_HOST
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
-#define CONFIG_USB_STORAGE
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 
 #define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO	76 /* HSIC2 HUB #RESET */
 #define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO	83 /* HSIC3 ETH #RESET */
 
 /* Enabled commands */
-#define CONFIG_CMD_DHCP		/* DHCP Support			*/
-#define CONFIG_CMD_PING
 
-/* USB Networking options */
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_SMSC95XX
-#define CONFIG_USB_ETHER_RNDIS
-#define CONFIG_USB_ETHER_ASIX
-#define CONFIG_USB_ETHER_MCS7830
+/* EEPROM */
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
+#define CONFIG_SYS_EEPROM_SIZE			256
 
-/* Max time to hold reset on this board, see doc/README.omap-reset-time */
-#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC	16296
+/* USB Networking options */
 
 /*
  * Miscellaneous configurable options
@@ -100,9 +73,7 @@
 #undef CONFIG_SYS_AUTOLOAD
 #undef CONFIG_EXTRA_ENV_SETTINGS
 #undef CONFIG_BOOTCOMMAND
-#undef CONFIG_BOOTDELAY
 
-#define CONFIG_BOOTDELAY		3
 #define CONFIG_SYS_AUTOLOAD		"no"
 
 #define CONFIG_EXTRA_ENV_SETTINGS \