X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fcanyonlands.h;h=d814012c415ee08e952e7397d8eff5b2f18bd902;hb=6c869637fef31e66380f0ea1d49690a2e26ec0d7;hp=e7896aa6c3839354ba03d50f6e741534e3711cda;hpb=499e7831e1baaac6bfb959213f1950c216fbc5ba;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index e7896aa..d814012 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -27,15 +27,32 @@ /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ -/* This config file is used for Canyonlands (460EX) and Glacier (460GT) */ -#ifndef CONFIG_CANYONLANDS +/* + * This config file is used for Canyonlands (460EX) Glacier (460GT) + * and Arches dual (460GT) + */ +#ifdef CONFIG_CANYONLANDS +#define CONFIG_460EX 1 /* Specific PPC460EX */ +#define CONFIG_HOSTNAME canyonlands +#else #define CONFIG_460GT 1 /* Specific PPC460GT */ +#ifdef CONFIG_GLACIER +#define CONFIG_HOSTNAME glacier #else -#define CONFIG_460EX 1 /* Specific PPC460EX */ +#define CONFIG_HOSTNAME arches +#define CONFIG_USE_NETDEV eth1 +#define CONFIG_BD_NUM_CPUS 2 +#endif #endif + #define CONFIG_440 1 #define CONFIG_4xx 1 /* ... PPC4xx family */ +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + #define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ @@ -47,68 +64,66 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE -#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ -#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE +#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ +#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */ +#define CONFIG_SYS_PCIE_BASE 0xc4000000 /* PCIe UTL regs */ -#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ -#define CFG_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */ -#define CFG_PCIE_BASE 0xc4000000 /* PCIe UTL regs */ +#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000 +#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000 +#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000 +#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000 -#define CFG_PCIE0_CFGBASE 0xc0000000 -#define CFG_PCIE1_CFGBASE 0xc1000000 -#define CFG_PCIE0_XCFGBASE 0xc3000000 -#define CFG_PCIE1_XCFGBASE 0xc3001000 - -#define CFG_PCIE0_UTLBASE 0xc08010000ULL /* 36bit physical addr */ +#define CONFIG_SYS_PCIE0_UTLBASE 0xc08010000ULL /* 36bit physical addr */ /* base address of inbound PCIe window */ -#define CFG_PCIE_INBOUND_BASE 0x000000000ULL /* 36bit physical addr */ +#define CONFIG_SYS_PCIE_INBOUND_BASE 0x000000000ULL /* 36bit physical addr */ /* EBC stuff */ -#define CFG_NAND_ADDR 0xE0000000 -#define CFG_BCSR_BASE 0xE1000000 -#define CFG_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space: 0xFF000000 */ -#define CFG_FLASH_BASE 0xFC000000 /* later mapped to this addr */ -#define CFG_FLASH_BASE_PHYS_H 0x4 -#define CFG_FLASH_BASE_PHYS_L 0xCC000000 -#define CFG_FLASH_BASE_PHYS (((u64)CFG_FLASH_BASE_PHYS_H << 32) | \ - (u64)CFG_FLASH_BASE_PHYS_L) -#define CFG_FLASH_SIZE (64 << 20) +#if !defined(CONFIG_ARCHES) +#define CONFIG_SYS_BCSR_BASE 0xE1000000 +#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped to this addr */ +#define CONFIG_SYS_FLASH_SIZE (64 << 20) +#else +#define CONFIG_SYS_FPGA_BASE 0xE1000000 +#define CONFIG_SYS_CPLD_ADDR (CONFIG_SYS_FPGA_BASE + 0x00080000) +#define CONFIG_SYS_CPLD_DATA (CONFIG_SYS_FPGA_BASE + 0x00080002) +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* later mapped to this addr */ +#define CONFIG_SYS_FLASH_SIZE (32 << 20) +#endif -#define CFG_OCM_BASE 0xE3000000 /* OCM: 16k */ -#define CFG_SRAM_BASE 0xE8000000 /* SRAM: 256k */ -#define CFG_LOCAL_CONF_REGS 0xEF000000 +#define CONFIG_SYS_NAND_ADDR 0xE0000000 +#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space: 0xFF000000 */ +#define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4 +#define CONFIG_SYS_FLASH_BASE_PHYS_L 0xCC000000 +#define CONFIG_SYS_FLASH_BASE_PHYS (((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) | \ + (u64)CONFIG_SYS_FLASH_BASE_PHYS_L) -#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals */ +#define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 64k */ +#define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ +#define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000 -#define CFG_AHB_BASE 0xE2000000 /* internal AHB peripherals */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal peripherals */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc()*/ +#define CONFIG_SYS_AHB_BASE 0xE2000000 /* internal AHB peripherals */ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in OCM) *----------------------------------------------------------------------*/ -#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ -#define CFG_INIT_RAM_END (4 << 10) -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ +#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -116,12 +131,12 @@ * Define here the location of the environment variables (FLASH). */ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CFG_NAND_CS 3 /* NAND chip connected to CSx */ +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */ #else -#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ -#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ -#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */ +#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ +#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */ #endif /* @@ -145,88 +160,88 @@ * This is the first official implementation of booting from 2k page sized * NAND devices (e.g. Micron 29F2G08AA 256Mbit * 8) */ -#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */ -#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from */ +#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */ +#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from */ /* this addr */ -#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) +#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) /* * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) */ -#define CFG_NAND_U_BOOT_OFFS (128 << 10) /* Offset to RAM U-Boot image */ -#define CFG_NAND_U_BOOT_SIZE (1 << 20) /* Size of RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10) /* Offset to RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_SIZE (1 << 20) /* Size of RAM U-Boot image */ /* * Now the NAND chip has to be defined (no autodetection used!) */ -#define CFG_NAND_PAGE_SIZE (2 << 10) /* NAND chip page size */ -#define CFG_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */ -#define CFG_NAND_PAGE_COUNT (CFG_NAND_BLOCK_SIZE / CFG_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) /* NAND chip page size */ +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */ +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE) /* NAND chip page count */ -#define CFG_NAND_BAD_BLOCK_POS 0 /* Location of bad block marker*/ -#define CFG_NAND_5_ADDR_CYCLE /* Fifth addr used (<=128MB) */ - -#define CFG_NAND_ECCSIZE 256 -#define CFG_NAND_ECCBYTES 3 -#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) -#define CFG_NAND_OOBSIZE 64 -#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) -#define CFG_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47, \ +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 /* Location of bad block marker*/ +#define CONFIG_SYS_NAND_5_ADDR_CYCLE /* Fifth addr used (<=128MB) */ + +#define CONFIG_SYS_NAND_ECCSIZE 256 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE) +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS) +#define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47, \ 48, 49, 50, 51, 52, 53, 54, 55, \ 56, 57, 58, 59, 60, 61, 62, 63} -#ifdef CFG_ENV_IS_IN_NAND +#ifdef CONFIG_ENV_IS_IN_NAND /* * For NAND booting the environment is embedded in the U-Boot image. Please take * look at the file board/amcc/canyonlands/u-boot-nand.lds for details. */ -#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE -#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE) -#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) #endif /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_FLASH_CFI /* The flash is CFI compatible */ -#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CFG_FLASH_CFI_AMD_RESET 1 /* Use AMD (Spansion) reset cmd */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* Use AMD (Spansion) reset cmd */ -#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#ifdef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) -#endif /* CFG_ENV_IS_IN_FLASH */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) +#endif /* CONFIG_ENV_IS_IN_FLASH */ /*----------------------------------------------------------------------- * NAND-FLASH related *----------------------------------------------------------------------*/ -#define CFG_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) -#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) +#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ /*------------------------------------------------------------------------------ * DDR SDRAM *----------------------------------------------------------------------------*/ #if !defined(CONFIG_NAND_U_BOOT) +#if !defined(CONFIG_ARCHES) /* * NAND booting U-Boot version uses a fixed initialization, since the whole * I2C SPD DIMM autodetection/calibration doesn't fit into the 4k of boot @@ -236,45 +251,112 @@ #define SPD_EEPROM_ADDRESS {0x50, 0x51} /* SPD i2c spd addresses*/ #define CONFIG_DDR_ECC 1 /* with ECC support */ #define CONFIG_DDR_RQDC_FIXED 0x80000038 /* fixed value for RQDC */ -#endif -#define CFG_MBYTES_SDRAM 512 /* 512MB */ + +#else /* defined(CONFIG_ARCHES) */ + +#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */ + +#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ +#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */ +#undef CONFIG_PPC4xx_DDR_METHOD_A + +/* DDR1/2 SDRAM Device Control Register Data Values */ +/* Memory Queue */ +#define CONFIG_SYS_SDRAM_R0BAS 0x0000f000 +#define CONFIG_SYS_SDRAM_R1BAS 0x00000000 +#define CONFIG_SYS_SDRAM_R2BAS 0x00000000 +#define CONFIG_SYS_SDRAM_R3BAS 0x00000000 +#define CONFIG_SYS_SDRAM_PLBADDULL 0x00000000 +#define CONFIG_SYS_SDRAM_PLBADDUHB 0x00000008 +#define CONFIG_SYS_SDRAM_CONF1LL 0x00001080 +#define CONFIG_SYS_SDRAM_CONF1HB 0x00001080 +#define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000 + +/* SDRAM Controller */ +#define CONFIG_SYS_SDRAM0_MB0CF 0x00000701 +#define CONFIG_SYS_SDRAM0_MB1CF 0x00000000 +#define CONFIG_SYS_SDRAM0_MB2CF 0x00000000 +#define CONFIG_SYS_SDRAM0_MB3CF 0x00000000 +#define CONFIG_SYS_SDRAM0_MCOPT1 0x05322000 +#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT0 0x01000000 +#define CONFIG_SYS_SDRAM0_MODT1 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT2 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT3 0x00000000 +#define CONFIG_SYS_SDRAM0_CODT 0x00800021 +#define CONFIG_SYS_SDRAM0_RTR 0x06180000 +#define CONFIG_SYS_SDRAM0_INITPLR0 0xb5380000 +#define CONFIG_SYS_SDRAM0_INITPLR1 0x82100400 +#define CONFIG_SYS_SDRAM0_INITPLR2 0x80820000 +#define CONFIG_SYS_SDRAM0_INITPLR3 0x80830000 +#define CONFIG_SYS_SDRAM0_INITPLR4 0x80810040 +#define CONFIG_SYS_SDRAM0_INITPLR5 0x80800532 +#define CONFIG_SYS_SDRAM0_INITPLR6 0x82100400 +#define CONFIG_SYS_SDRAM0_INITPLR7 0x8a080000 +#define CONFIG_SYS_SDRAM0_INITPLR8 0x8a080000 +#define CONFIG_SYS_SDRAM0_INITPLR9 0x8a080000 +#define CONFIG_SYS_SDRAM0_INITPLR10 0x8a080000 +#define CONFIG_SYS_SDRAM0_INITPLR11 0x80000432 +#define CONFIG_SYS_SDRAM0_INITPLR12 0x808103c0 +#define CONFIG_SYS_SDRAM0_INITPLR13 0x80810040 +#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000 +#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000 +#define CONFIG_SYS_SDRAM0_RQDC 0x80000038 +#define CONFIG_SYS_SDRAM0_RFDC 0x00000257 +#define CONFIG_SYS_SDRAM0_RDCC 0x40000000 +#define CONFIG_SYS_SDRAM0_DLCR 0x03000091 +#define CONFIG_SYS_SDRAM0_CLKTR 0x40000000 +#define CONFIG_SYS_SDRAM0_WRDTR 0x82000823 +#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000 +#define CONFIG_SYS_SDRAM0_SDTR2 0x42204243 +#define CONFIG_SYS_SDRAM0_SDTR3 0x090c0d1a +#define CONFIG_SYS_SDRAM0_MMODE 0x00000432 +#define CONFIG_SYS_SDRAM0_MEMODE 0x00000004 +#endif /* !defined(CONFIG_ARCHES) */ +#endif /* !defined(CONFIG_NAND_U_BOOT) */ + +#define CONFIG_SYS_MBYTES_SDRAM 512 /* 512MB */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F - -#define CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR (0xa8>>1) -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ + +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* I2C SYSMON (LM75, AD7414 is almost compatible) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_AD7414 1 /* use AD7414 */ #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 +#if defined(CONFIG_ARCHES) +#define CONFIG_SYS_I2C_DTT_ADDR 0x4a /* AD7414 I2C address */ +#endif + +#if !defined(CONFIG_ARCHES) /* RTC configuration */ #define CONFIG_RTC_M41T62 1 -#define CFG_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#endif /*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/ #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ -#define CONFIG_PHY1_ADDR 1 + #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 + +#if !defined(CONFIG_ARCHES) +#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ +#define CONFIG_PHY1_ADDR 1 /* Only Glacier (460GT) has 4 EMAC interfaces */ #ifdef CONFIG_460GT #define CONFIG_PHY2_ADDR 2 @@ -282,14 +364,35 @@ #define CONFIG_HAS_ETH2 #define CONFIG_HAS_ETH3 #endif -#define CONFIG_NET_MULTI 1 + +#else /* defined(CONFIG_ARCHES) */ + +#define CONFIG_FIXED_PHY 0xFFFFFFFF +#define CONFIG_PHY_ADDR CONFIG_FIXED_PHY +#define CONFIG_PHY1_ADDR 0 +#define CONFIG_PHY2_ADDR 1 +#define CONFIG_HAS_ETH2 + +#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \ + {devnum, speed, duplex} +#define CONFIG_SYS_FIXED_PHY_PORTS \ + CONFIG_SYS_FIXED_PHY_PORT(0, 1000, FULL) + +#define CONFIG_M88E1112_PHY + +/* + * For the GPCS_PHYx_ADDR PHY address, choose some PHY address not + * used by CONFIG_PHYx_ADDR + */ +#define CONFIG_GPCS_PHY_ADDR 0xA +#define CONFIG_GPCS_PHY1_ADDR 0xB +#define CONFIG_GPCS_PHY2_ADDR 0xC +#endif /* !defined(CONFIG_ARCHES) */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_DYNAMIC_ANEG 1 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - /*----------------------------------------------------------------------- * USB-OHCI *----------------------------------------------------------------------*/ @@ -297,113 +400,69 @@ #ifdef CONFIG_460EX #define CONFIG_USB_OHCI_NEW #define CONFIG_USB_STORAGE -#undef CFG_OHCI_BE_CONTROLLER /* 460EX has little endian descriptors */ -#define CFG_OHCI_SWAP_REG_ACCESS /* 460EX has little endian register */ -#define CFG_OHCI_USE_NPS /* force NoPowerSwitching mode */ -#define CFG_USB_OHCI_REGS_BASE (CFG_AHB_BASE | 0xd0000) -#define CFG_USB_OHCI_SLOT_NAME "ppc440" -#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 -#endif - -/*----------------------------------------------------------------------- - * Default environment - *----------------------------------------------------------------------*/ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifdef CONFIG_CANYONLANDS -#define CONFIG_HOSTNAME canyonlands -#define CFG_BOOTFILE "bootfile=canyonlands/uImage\0" -#define CFG_DTBFILE "fdt_file=canyonlands/canyonlands.dtb\0" -#else -#define CONFIG_HOSTNAME glacier -#define CFG_BOOTFILE "bootfile=glacier/uImage\0" -#define CFG_DTBFILE "fdt_file=glacier/glacier.dtb\0" +#undef CONFIG_SYS_OHCI_BE_CONTROLLER /* 460EX has little endian descriptors */ +#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS /* 460EX has little endian register */ +#define CONFIG_SYS_OHCI_USE_NPS /* force NoPowerSwitching mode */ +#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_AHB_BASE | 0xd0000) +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 #endif -#define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_DTBFILE \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "net_nfs=tftp 400000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty;" \ - "bootm 400000 - ${fdt_addr}\0" \ - "net_nfs_fdt=net_nfs\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "rootpath=/opt/eldk/ppc_4xxFP\0" \ - "fdt_addr=800000\0" \ +/* + * Default environment variables + */ +#if !defined(CONFIG_ARCHES) +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fc000000\0" \ + "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 ${hostname}/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 ${hostname}/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 100000;nand write 200000 0 100000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK +#else /* defined(CONFIG_ARCHES) */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + "kernel_addr=fe000000\0" \ + "fdt_addr=fe1e0000\0" \ + "ramdisk_addr=fe200000\0" \ + "pciconfighost=1\0" \ + "pcie_mode=RP:RP\0" \ + "ethprime=ppc_4xx_eth1\0" \ + "" +#endif /* !defined(CONFIG_ARCHES) */ /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP +#if defined(CONFIG_ARCHES) #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM -#ifdef CONFIG_460EX +#elif defined(CONFIG_CANYONLANDS) +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DTT #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT +#define CONFIG_CMD_NAND +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP #define CONFIG_CMD_USB +#elif defined(CONFIG_GLACIER) +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DTT +#define CONFIG_CMD_NAND +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP +#else +#error "board type not defined" #endif /* Partitions */ @@ -412,41 +471,6 @@ #define CONFIG_ISO_PARTITION /*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - -#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " -#endif - -/*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ /* General PCI */ @@ -456,26 +480,41 @@ #define CONFIG_PCI_CONFIG_HOST_BRIDGE /* Board-specific PCI */ -#define CFG_PCI_TARGET_INIT /* let board init pci target */ -#undef CFG_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ +#undef CONFIG_SYS_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif +#ifdef CONFIG_460GT +#if defined(CONFIG_ARCHES) +/*----------------------------------------------------------------------- + * RapidIO I/O and Registers + *----------------------------------------------------------------------*/ +#define CONFIG_RAPIDIO +#define CONFIG_SYS_460GT_SRIO_ERRATA_1 + +#define SRGPL0_REG_BAR 0x0000000DAA000000ull /* 16MB */ +#define SRGPL0_CFG_BAR 0x0000000DAB000000ull /* 16MB */ +#define SRGPL0_MNT_BAR 0x0000000DAC000000ull /* 16MB */ +#define SRGPL0_MSG_BAR 0x0000000DAD000000ull /* 16MB */ +#define SRGPL0_OUT_BAR 0x0000000DB0000000ull /* 256MB */ + +#define CONFIG_SYS_SRGPL0_REG_BAR 0xAA000000 /* 16MB */ +#define CONFIG_SYS_SRGPL0_CFG_BAR 0xAB000000 /* 16MB */ +#define CONFIG_SYS_SRGPL0_MNT_BAR 0xAC000000 /* 16MB */ +#define CONFIG_SYS_SRGPL0_MSG_BAR 0xAD000000 /* 16MB */ + +#define CONFIG_SYS_I2ODMA_BASE 0xCF000000 +#define CONFIG_SYS_I2ODMA_PHYS_ADDR 0x0000000400100000ull + +#define CONFIG_PPC4XX_RAPIDIO_PROMISCUOUS_MODE +#undef CONFIG_PPC4XX_RAPIDIO_DEBUG +#undef CONFIG_PPC4XX_RAPIDIO_IN_BAR_USE_OCM +#define CONFIG_PPC4XX_RAPIDIO_USE_HB_PLB +#undef CONFIG_PPC4XX_RAPIDIO_LOOPBACK +#endif /* CONFIG_ARCHES */ +#endif /* CONFIG_460GT */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup @@ -489,38 +528,63 @@ * EBC address which accepts bigger regions: * * 0xfc00.0000 -> 4.cc00.0000 + * + * Arches has 32MBytes of NOR FLASH (Spansion 29GL256), it will be + * remapped to: + * + * 0xfe00.0000 -> 4.ce00.0000 */ #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) /* Memory Bank 3 (NOR-FLASH) initialization */ -#define CFG_EBC_PB3AP 0x10055e00 -#define CFG_EBC_PB3CR (CFG_BOOT_BASE_ADDR | 0x9a000) +#define CONFIG_SYS_EBC_PB3AP 0x10055e00 +#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000) /* Memory Bank 0 (NAND-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x018003c0 -#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/ +#define CONFIG_SYS_EBC_PB0AP 0x018003c0 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/ #else /* Memory Bank 0 (NOR-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x10055e00 -#define CFG_EBC_PB0CR (CFG_BOOT_BASE_ADDR | 0x9a000) +#define CONFIG_SYS_EBC_PB0AP 0x10055e00 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000) +#if !defined(CONFIG_ARCHES) /* Memory Bank 3 (NAND-FLASH) initialization */ -#define CFG_EBC_PB3AP 0x018003c0 -#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/ +#define CONFIG_SYS_EBC_PB3AP 0x018003c0 +#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/ #endif +#endif /*defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */ +#if !defined(CONFIG_ARCHES) /* Memory Bank 2 (CPLD) initialization */ -#define CFG_EBC_PB2AP 0x00804240 -#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x18000) /* BAS=CPLD,BS=1M,BU=RW,BW=32bit */ +#define CONFIG_SYS_EBC_PB2AP 0x00804240 +#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_BCSR_BASE | 0x18000) /* BAS=CPLD,BS=1M,BU=RW,BW=32bit */ -#define CFG_EBC_CFG 0xB8400000 /* EBC0_CFG */ +#else /* defined(CONFIG_ARCHES) */ + +/* Memory Bank 1 (FPGA) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x7f8ffe80 +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FPGA_BASE | 0x3a000) /* BAS=FPGA,BS=2MB,BU=R/W,BW=16bit*/ +#endif /* !defined(CONFIG_ARCHES) */ + +#define CONFIG_SYS_EBC_CFG 0xB8400000 /* EBC0_CFG */ + +/* + * Arches doesn't use PerCS3 but GPIO43, so let's configure the GPIO + * pin multiplexing correctly + */ +#if defined(CONFIG_ARCHES) +#define GPIO43_USE GPIO_SEL /* On Arches this pin is used as GPIO */ +#else +#define GPIO43_USE GPIO_ALT1 /* On Glacier this pin is used as ALT1 -> PerCS3 */ +#endif /* * PPC4xx GPIO Configuration */ #ifdef CONFIG_460EX /* 460EX: Use USB configuration */ -#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ { \ /* GPIO Core 0 */ \ {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \ @@ -594,7 +658,7 @@ } #else /* 460GT: Use EMAC2+3 configuration */ -#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ { \ /* GPIO Core 0 */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \ @@ -643,7 +707,7 @@ {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \ {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \ {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO43_USE, GPIO_OUT_0},/* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \ {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \ {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \ {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \ @@ -668,8 +732,4 @@ } #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */