X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fcanyonlands.h;h=b495d0645b603427cf96468a6199b4150d577e37;hb=da684a646d0c94f7a6126e7ecf110278691465a6;hp=7a1499d2e3a579b6b8134f413f884a16472d5709;hpb=e1cc4d31f889428a4ca73120951389c756404184;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h
index 7a1499d..b495d06 100644
--- a/include/configs/canyonlands.h
+++ b/include/configs/canyonlands.h
@@ -13,8 +13,6 @@
 
 #include <linux/kconfig.h>
 
-#define CONFIG_SYS_GENERIC_BOARD
-
 /*-----------------------------------------------------------------------
  * High Level Configuration Options
  *----------------------------------------------------------------------*/
@@ -49,7 +47,6 @@
 
 #define CONFIG_SYS_CLK_FREQ	66666667	/* external freq to pll	*/
 
-#define CONFIG_BOARD_EARLY_INIT_F		/* Call board_early_init_f */
 #define CONFIG_BOARD_EARLY_INIT_R		/* Call board_early_init_r */
 #define CONFIG_MISC_INIT_R			/* Call misc_init_r */
 #define CONFIG_BOARD_TYPES			/* support board types */
@@ -250,7 +247,6 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
 
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR		(0xa8>>1)
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
@@ -265,18 +261,6 @@
 #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET	0
 #define CONFIG_4xx_CONFIG_BLOCKSIZE		16
 
-/* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
-#define CONFIG_DTT_LM75				/* ON Semi's LM75	*/
-#define CONFIG_DTT_AD7414			/* use AD7414		*/
-#define CONFIG_DTT_SENSORS	{0}		/* Sensor addresses	*/
-#define CONFIG_SYS_DTT_MAX_TEMP	70
-#define CONFIG_SYS_DTT_LOW_TEMP	-30
-#define CONFIG_SYS_DTT_HYSTERESIS	3
-
-#if defined(CONFIG_ARCHES)
-#define CONFIG_SYS_I2C_DTT_ADDR	0x4a		/* AD7414 I2C address	*/
-#endif
-
 #if !defined(CONFIG_ARCHES)
 /* RTC configuration */
 #define CONFIG_RTC_M41T62
@@ -336,7 +320,6 @@
 /* Only Canyonlands (460EX) has USB */
 #ifdef CONFIG_460EX
 #define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
 #undef CONFIG_SYS_OHCI_BE_CONTROLLER		/* 460EX has little endian descriptors	*/
 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS	/* 460EX has little endian register	*/
 #define CONFIG_SYS_OHCI_USE_NPS		/* force NoPowerSwitching mode		*/
@@ -377,45 +360,29 @@
 /*
  * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_CMD_CHIP_CONFIG
 #if defined(CONFIG_ARCHES)
-#define CONFIG_CMD_DTT
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SDRAM
 #elif defined(CONFIG_CANYONLANDS)
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SATA
 #define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
 #elif defined(CONFIG_GLACIER)
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DTT
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
 #else
 #error "board type not defined"
 #endif
 
 /* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
 
 /*-----------------------------------------------------------------------
  * PCI stuff
  *----------------------------------------------------------------------*/
 /* General PCI */
-#define CONFIG_PCI			/* include pci support	        */
 #define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play   */
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup  */
 #define CONFIG_PCI_CONFIG_HOST_BRIDGE