X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fbubinga.h;h=acce82f621159f896143dd8a2bf1444a640c983a;hb=29f8f58ff40c67f7f2e11afd1715173094e52ac2;hp=4a79835d6ac3c30e938f4a654daaabe441e02c67;hpb=038ccac511214b062c56f22b9413f784b86bcd87;p=platform%2Fkernel%2Fu-boot.git diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h index 4a79835..acce82f 100644 --- a/include/configs/bubinga.h +++ b/include/configs/bubinga.h @@ -37,6 +37,12 @@ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME bubinga +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ @@ -80,102 +86,33 @@ #define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ #endif -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=bubinga\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/bubinga/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff80000\0" \ "ramdisk_addr=fff90000\0" \ - "load=tftp 100000 /tftpboot/bubinga/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ "" -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ +#define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_ASKENV | \ - CFG_CMD_CACHE | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_EEPROM | \ - CFG_CMD_ELF | \ - CFG_CMD_I2C | \ - CFG_CMD_IRQ | \ - CFG_CMD_MII | \ - CFG_CMD_NET | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SDRAM | \ - CFG_CMD_SNTP ) - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ - /* - * Miscellaneous configurable options + * Commands additional to the ones defined in amcc-common.h */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_CMD_DATE +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ /* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. @@ -191,33 +128,16 @@ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ -#if (CONFIG_COMMANDS & CFG_CMD_EEPROM) +#if defined(CONFIG_CMD_EEPROM) #define CFG_I2C_EEPROM_ADDR 0x50 /* I2C boot EEPROM (24C02W) */ #define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ #endif @@ -257,21 +177,9 @@ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_SRAM_BASE 0xFFF00000 #define CFG_FLASH_BASE 0xFFF80000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization @@ -287,7 +195,7 @@ #define CFG_FLASH_WORD_SIZE unsigned char #ifdef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ @@ -307,14 +215,6 @@ #define CFG_ENV_ADDR \ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ #endif -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405EP CPU */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Init Memory Controller: @@ -416,17 +316,4 @@ #define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */ #define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */ -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - #endif /* __CONFIG_H */