X-Git-Url: http://review.tizen.org/git/?a=blobdiff_plain;f=include%2Fconfigs%2Fbf533-stamp.h;h=516fe2d021532ba68f6c03447525ba67da1875fc;hb=0ff27d4a94637d4b1937c625d33212375bd118d9;hp=f5b9658294387e3ebc89cf38c1e719b30c4a5800;hpb=215ab45a67672a7c1ceb347f7b74c94323415222;p=platform%2Fkernel%2Fu-boot.git

diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
index f5b9658..516fe2d 100644
--- a/include/configs/bf533-stamp.h
+++ b/include/configs/bf533-stamp.h
@@ -1,5 +1,5 @@
 /*
- * U-boot - Configuration file for BF533 STAMP board
+ * U-Boot - Configuration file for BF533 STAMP board
  */
 
 #ifndef __CONFIG_BF533_STAMP_H__
@@ -7,7 +7,6 @@
 
 #include <asm/config-pre.h>
 
-
 /*
  * Processor Settings
  */
@@ -53,7 +52,6 @@
 #define CONFIG_SYS_MONITOR_LEN	(256 * 1024)
 #define CONFIG_SYS_MALLOC_LEN	(384 * 1024)
 
-
 /*
  * Network Settings
  */
@@ -68,9 +66,6 @@
 		SSYNC(); \
 	} while (0)
 #define CONFIG_HOSTNAME		bf533-stamp
-/* Uncomment next line to use fixed MAC address */
-/* #define CONFIG_ETHADDR	02:80:ad:20:31:b8 */
-
 
 /* I2C */
 #define CONFIG_SYS_I2C
@@ -98,10 +93,10 @@
  */
 #define CONFIG_BFIN_SPI
 #define CONFIG_ENV_SPI_MAX_HZ	30000000
+/*
 #define CONFIG_SF_DEFAULT_SPEED	30000000
-#define CONFIG_SPI_FLASH
 #define CONFIG_SPI_FLASH_ALL
-
+*/
 
 /*
  * Env Storage Settings
@@ -136,7 +131,6 @@
 	common/env_embedded.o (.text*);
 #endif
 
-
 /*
  * I2C Settings
  */
@@ -158,7 +152,6 @@
 /* #define CONFIG_STAMP_CF */
 #if defined(CONFIG_STAMP_CF)
 #define CONFIG_MISC_INIT_R
-#define CONFIG_DOS_PARTITION	1
 #undef  CONFIG_IDE_8xx_DIRECT		/* no pcmcia interface required */
 #undef  CONFIG_IDE_LED			/* no led for ide supported */
 #undef  CONFIG_IDE_RESET		/* no reset for ide supported */
@@ -179,7 +172,6 @@
 #define CONFIG_EBIU_AMBCTL1_VAL	0x99B3ffc2
 #endif
 
-
 /*
  * Misc Settings
  */
@@ -193,26 +185,8 @@
 /* #define CONFIG_SHOW_BOOT_PROGRESS */
 
 /* define to enable run status via led */
-/* #define CONFIG_STATUS_LED */
-#ifdef CONFIG_STATUS_LED
-#define CONFIG_GPIO_LED
-#define CONFIG_BOARD_SPECIFIC_LED
-/* use LED0 to indicate booting/alive */
-#define STATUS_LED_BOOT 0
-#define STATUS_LED_BIT GPIO_PF2
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
-/* use LED1 to indicate crash */
-#define STATUS_LED_CRASH 1
-#define STATUS_LED_BIT1 GPIO_PF3
-#define STATUS_LED_STATE1 STATUS_LED_ON
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-/* #define STATUS_LED_BIT2 GPIO_PF4 */
-#endif
 
 /* define to enable splash screen support */
-/* #define CONFIG_VIDEO */
-
 
 /*
  * Pull in common ADI header for remaining command/environment setup